EN 1615 EN
Disclaimers
THE LIMITED WARRANTIES SET FORTH HEREIN ARE IN LIEU OF AND EXCLUDE ALL OTHER EXPRESS OR IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR
APPLICATION, AND ALL OTHER OBLIGATIONS ON THE PART OF ANKER/SOLIX UNLESS SUCH OTHER WARRANTIES AND
OBLIGATIONS ARE AGREED TO IN WRITING BY ANKER/SOLIX. SOME JURISDICTIONS LIMIT OR DO NOT PERMIT DISCLAIMERS OF
WARRANTY, SO THIS PROVISION MAY NOT APPLY TO THE BUYER IN SUCH JURISDICTIONS.
Limitation of Liability
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANKER/SOLIX HEREBY DISCLAIMS AND SHALL HAVE NO
RESPONSIBILITY OR LIABILITY WHATSOEVER FOR, DAMAGE OR INJURY TO PERSONS OR PROPERTY OR FOR OTHER LOSS OR
INJURY RESULTING FROM ANY CAUSE WHATSOEVER ARISING OUT OF OR RELATED TO ANY OF ITS PRODUCTS OR THEIR USE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL ANKER/SOLIX BE LIABLE
TO THE BUYER, OR TO ANY THIRD PARTY CLAIMING THROUGH OR UNDER THE BUYER, FOR ANY LOST PROFITS, LOSS OF USE,
OR EQUIPMENT DOWNTIME, OR FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND, HOWSOEVER
ARISING, RELATED TO THE PRODUCTS, EVEN IF ANKER/SOLIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANKER's/SOLIX's AGGREGATE LIABILITY, IF ANY, IN DAMAGES
OR OTHERWISE, SHALL NOT EXCEED THE PURCHASE PRICE PAID TO ANKER/SOLIX BY THE BUYER FOR THE PRODUCT IN THE
CASE OF A WARRANTY CLAIM.
THE BUYER ACKNOWLEDGES THAT THE FOREGOING LIMITATIONS OF LIABILITY ARE AN ESSENTIAL ELEMENT OF THE
AGREEMENT BETWEEN THE PARTIES AND THAT IN THE ABSENCE OF SUCH LIMITATIONS THE PURCHASE PRICE OF THE
PRODUCTS WOULD BE SUBSTANTIALLY DIFFERENT. SOME JURISDICTIONS LIMIT OR DO NOT PERMIT DISCLAIMERS OF
LIABILITY, SO THIS PROVISION MAY NOT APPLY TO THE BUYER IN SUCH JURISDICTIONS. SOME JURISDICTIONS DO NOT ALLOW
LIMITATIONS ON THE EXCLUSION OF DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO THE BUYER IN
SUCH JURISDICTIONS.
YOU MAY HAVE SPECIFIC LEGAL RIGHTS OUTSIDE THIS WARRANTY, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE OR COUNTRY TO COUNTRY. THIS LIMITED WARRANTY DOES NOT AFFECT ANY ADDITIONAL RIGHTS YOU HAVE
UNDER LAWS IN YOUR JURISDICTION GOVERNING THE SALE OF CONSUMER GOODS. SOME STATES OR COUNTRIES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE LIMITATIONS OR EXCLUSIONS
IN THIS LIMITED WARRANTY STATEMENT MAY NOT APPLY TO YOU IN THOSE AREAS.
A NOTE:
The installation and handling of PV Products would better be performed by qualified professionals. Please read the safety and
installation instructions before using the products.
When returning items with a prepaid shipping label provided by Anker, Anker takes responsibility for any damage or loss
incurred in transit. When returning items for non-quality issues, the buyer assumes responsibility for any damage or loss
incurred in transit. Anker does not provide refunds for items damaged in transit for non-quality-related warranty claims.
Troubleshooting
1.Check the connection to the utility grid. Verify that the utility voltage and frequency are within the allowable ranges shown on
the label of the microinverter.
2.Verify if utility power is present in the inverter by removing AC, then DC power. Do not disconnect the DC wires when the
microinverter is producing power. Reconnect the DC module connectors and the LED should blink.
3.Check the interconnection harness of the AC branch circuit. Verify that the microinverter is powered by the utility grid as
described in the previous step.
4.Ensure all AC disconnects are closed and functioning properly.
5.Make sure the DC voltage on the solar panels does not exceed the range listed on the microinverter label.
6.Check the DC connections between the microinverter and the solar panel.
7.When changing Wi-Fi networks, disconnect the AC wires first.
Maintenance
Disconnect the Microinverter from the Solar Panel
1. Disconnect the Schuko connection cable.
2. Disconnect the Schuko connection cable from the microinverter.
3. Protect the connector with insulation and waterproof protection materials.
4. Using a DC current probe, verify that there is no current flow in the DC wires between the solar panel and the microinverter.
5. Measure DC currents with care. Zero drift in the meter may occur over time.
6. Disconnect the solar panel's DC wire connectors from the microinverter.
Warranty & Customer Service
12-Year Limited Warranty for Anker RS40 Rigid Solar Panel
15-Year Limited Warranty for Anker RS40P Rigid Solar Panel
10-Year Limited Warranty for Anker MI60 Microinverter
2-Year Limited Warranty for Anker Adjustable Solar Panel Tilt Mount
1-Year Limited Warranty for Anker Solar Panel Extension Cable and Anker MI60 to Schuko Connection Cable
Lifetime Technical Support
support@anker.com
(DE) +49 (800) 000 2522
To Previous Page
Loading...
