Enroll
Delete
Verify Mode
[M]
Select [User]
[OK]
Select [Enroll]
[OK]
Input user ID
Enroll User: Each user can register two fingerprints, one password and one card.
Explanation
1
Item
Factory default
setting
1-99999999
Device ID of the unit which is required in software
communication
Dev ID:
Tips: WorkCode indicates the work type，easily distinguishes which attendance record
is related to which work type.
Explanation
Max 999999
Min 0
Item
Factory default
setting
0-999999 Valid scope for the Workcode
WorkCode:
Item Explanation
Factory default
setting
Any
RF+PW
RF+FP
PW+FP
Fingerprint only, Card only or ID+Password only
It requires both Card and Password verification
together
It requires both Card and Fingerprint
verification together
It requires both Password and Fingerprint verification
together
Enter the user ID first, then verify the fingerprint
Any
ID+FP
Verify Mode:
TCP/IP
Power
G-LED
R-LED
D0
D1
W0
12V OUT
DOOR OPEN
W1
12V IN
COM
NO
NC
GND
GND
U Disk
Mini USB
Flash Memory
USB
TCP/IP
3.FN key
(The function with mark in the menu is for the specific
model unit. Please follow as actual product’s menu. )
(ID number range:0-999999)
Tips: Group setup is used for managing the access control privileges. Each group can
contain 4 time zones.The default setting: G01．
Explanation
G01
Item
Factory default
setting
G00
G01
G02-16
The user in Group00 can not open the door
The user in Group01 can open the door anytime
It is according to the Group & Time zone setting which
can be set through the software
Group Setup:
V1.2
M→[Setup]→[OK]→[System]→[OK]→[Dev ID]→[OK]→Input the device’s ID
→[OK]→[C]→[OK].
M→ [Setup]→[OK]→[System]→[OK]→[WorkCode Scope]→[OK]
→Input Max→[OK]→Input Min→[OK] →[C]→[OK].
M→[User]→[OK]→[Verify Mode]→[OK]→[OK]→Input employee ID→[OK]→
Use [IN／ ]/[OUT/ ] to select ‘ANY/RF+FP/PW+FP/RF+PW/ID+FP’→[OK]→[OK].
ExplanationItem
Factory default
setting
Server Mode
192.168.0.218
255.255.255.0
192.168.0.1
192.168.0.7
5010
Mode
IP Address
Subnet Mask
MAC Address
Gateway IP
Server IP
Server Port
Net:
M→ [Setup]→[OK]→[System]→[OK]→[Net]→[OK]→to select [Mode/IP Address/Subnet Mask
/MAC Address/Gateway IP/Server IP/Server Port]→[OK]→Modify parameters→[C]→[OK].
M→[User]→[OK]→[Group Setup]→[OK]→[OK]→
Input employee ID→[OK]→Input the group ID→[OK]→[OK].
▼
▼
Explanation
Related Language
Item
Factory default
setting
Language
Contains 11 languages:
ENG(English), FRCH(French), GERM(German), SPAN(Spanish),
PTG(Portuguese), ITA(Italian), BULG(Bulgarian), SLVK(Slovak),
HUNG(Hungarian), SLVN(Slovenian), TURK(Turkish)
Language:
M→[Setup]→[OK]→[System]→[OK]→[Language]→[OK]→
Use [IN/ ]/[OUT/ ] to select ENG/FRCH/GERM/...→[OK]→[C]→[OK].
ExplanationItem
Precision, Volume, Auto off, Auto Update, Image Disp., Log Alert, Re-Verify
Place finger flat on the sensor surface. Sliding, Rolling or Moving finger
during the enrollment process.
Do not remove finger during
the enrollment process.
Using the tip of your finger.
A Standard USB flash drive with a
maximum capacity to 2GB of RAM
is required.
TCP/IP Server mode: Common network mode
TCP/IP Client mode: Only communicate
with the PC which has static IP
Set terminal IP address when communication
of TCP/IP, IP address
must be a static
IP address
Subnet Mask of the LAN
Unique Physical address of the network moudle. This
setting can not be modified.
Default Gateway of the LAN
The IP address of the Sever Machine
when using Client Mode TCP/IP
communication.
It’s the Software Port number used when the
read is configured for TCP/IP communication
Image Disp.
The duration of time in which the terminal will ignore
repeated attempts for authentication.
[No]: Disable the function; Max. value is 250 min.
Re-Verify
Auto update means the previous lower quality fingerprint
template will be automatically replaced by the new higher
quality one during fingerprint verification.
Choose to display the fingerprint image on the screen during
the verification process. [Yes] - show fingerprint image,
[No] - not show fingerprint image
Set the time duration for an idle clock to go into sleep
mode. No-[Not Off], 250min-[Max Time].
Set the terminal voice volume.
0-[mute], 5-[Max].
Set terminal fingerprint matching precision.
0-[Normal],1-[Good], 2-[Exact].
Precision
Volume
Auto off
Log Alert
Auto Update
The terminal will alarm when the memory capacity
is less than the [Log Alert] value.[No]-Not alarm,
Max. value 5,000.
Wiegand Output
Wiegand Input
Need help?
General
