Aprimatic ZT44 ABC User Manual

- 14 -
English
AP030
R
Characteristics
1
1.1 Technical data ........................................................................................................................................................................................... 14
1.2 Choosing the type of automation .............................................................................................................................................................. 15
1.3 General characteristics ............................................................................................................................................................................. 15
Preliminary operations
2
2.1 Preliminary checks.................................................................................................................................................................................... 15
2.2 Checking the operator components .......................................................................................................................................................... 16
2.2.1 List of components (B4) ............................................................................................................................................................................ 16
2.3 Preparing the mounting............................................................................................................................................................................. 16
2.4 Components layout (B2) ........................................................................................................................................................................... 17
2.5 Electrical connections ............................................................................................................................................................................... 17
3
3.1 Positioning of mountings ........................................................................................................................................................................... 18
3.2 Preparing the rear mounting ..................................................................................................................................................................... 18
3.2.1 Preparations for rear operator mounting on iron posts ............................................................................................................................. 18
3.2.2 Preparations for rear operator mountings on masonry posts.................................................................................................................... 19
3.2.3 Preparations for rear operator mounting on masonry posts with inset...................................................................................................... 19
3.3 Fitting the rear anchorage plates .............................................................................................................................................................. 20
3.4 Fitting the rear operator mounting............................................................................................................................................................. 20
3.5 Positioning the front mounting................................................................................................................................................................... 20
3.6 Temporary rear fi tting of the operator........................................................................................................................................................ 21
3.7 Frontal positioning of the operator ............................................................................................................................................................ 21
3.8 Final fi tting of the operator ........................................................................................................................................................................ 22
3.9 Final assembly .......................................................................................................................................................................................... 22
3.9.1 Bleeding .................................................................................................................................................................................................... 22
3.9.2 Adjusting the brake in close position......................................................................................................................................................... 22
3.9.3 Slowing down the operator opening (C29)................................................................................................................................................ 23
3.9.4 Final assembly .......................................................................................................................................................................................... 23
Finals operations
4
4.1 Checks and setting.................................................................................................................................................................................... 24
5
5.1 Emergency operation - useof manual release .......................................................................................................................................... 25
5.2 Notes for the installer ................................................................................................................................................................................ 25
5.2.1 Maintenance ............................................................................................................................................................................................. 25
5.2.2 Trouble-shooting guide.............................................................................................................................................................................. 25
1.1 TECHNICAL DATA
Installation
Notes for the user
Index / Characteristics
Warning
!
The noise level of the above models, with reference to the working of the operator independently of the gate leaf and the gate post,
falls within the maximum limits set by EEC standards.
230 V±10% 50 Hz
230 V±10% 50 Hz
ZT44 ABC ZT44 SF DS
CHARACTERISTICS
Single-phase system voltage
Power absorption
Mean pressure
Thrust force at 10 bar
Traction force at 15 bar
Rod return time (complete stroke)
Rod advance time
Max leaf length
Min leaf length
Operating temperature range
Max distance between centres for mounting holes
with fully extended rod
Max stroke - standard arm
Weight with oil
Oil quantity
Oil type
250W 250W
962 N
30 bar
30 bar
1140 N
-20˚ / + 70˚C
1002 mm
± 5
270 mm
8 Kg
0,6 lt.
Aprimatic Oil HC13
ZT42 (B-SR)
230 V±10% 50 Hz
250W
30 bar
962 N
962 N
1140 N 1140 N
12,5 sec 17,5 sec 17,5 sec
15,5 sec 21,5 sec
21,5 sec
1,2 m 1,8 m
4 m
0,8 m 1,2 m
1,2 m
-20˚ / + 70˚C
-20˚ / + 70˚C
1002 mm
± 5
1002 mm
± 5
190 mm
270 mm
8 Kg
8 Kg
0,6 lt.
0,6 lt.
Aprimatic Oil HC13
Aprimatic Oil HC13
Protection degree IP 55 IP 55 IP 55

Aprimatic ZT44 ABC Specifications

General

Motor Voltage	24 Vdc
Operating Temperature	-20°C to +55°C
Protection Level	IP44
Power Supply	230V AC
Safety Features	Obstacle detection