The Aquasure Fortitude Pro Series is a whole house water treatment system designed for self-installation, offering comprehensive water filtration and treatment for residential use. The system aims to provide optimum performance and protection against contaminants, ensuring improved water quality throughout the home.
Function Description:
The Aquasure Fortitude Pro Series is a multi-stage whole house water treatment system. It typically consists of a pleated sediment pre-filter and a larger media tank with a valve head. The pre-filter is designed to remove larger particles and sediment from the incoming water, protecting the main treatment system and extending its lifespan. The main media tank, pre-filled with a specialized media, further treats the water to remove various impurities, enhancing overall water quality. The system is designed to be installed on the main water supply line of a house, treating all water before it is distributed to faucets and appliances.
Important Technical Specifications:
- Water Temperature Parameter:
- Maximum: 100° F (37.8° C)
- Minimum: 40° F (4.4° C)
- Water Pressure Parameter:
- Maximum: 75 PSI (5.98 kg/cm²)
- Minimum: 20 PSI (1.41 kg/cm²)
- Pressure reducer recommended if PSI exceeds 75 psi.
- pH Parameter:
- Pre-filter: The system includes a pleated sediment pre-filter. The size of the pre-filter may vary depending on the system configuration. The manual shows a 10" pleated sediment filter as an example.
- Main Media Tank: Aquasure High Strength Fiberglass Tank, pre-filled with media.
- Valve Head: Aquasure MFV Valve Head with 1" in/out ports and a Media Reset Backwash Port.
- Fittings: Includes various nipples (1" to 1" and 1" to 3/4") and O-rings for installation.
- Recommended Tool List for System Installation: Variable Speed Drill, Drill Bit, Bolt Bit, Adjustment Wrench, Level Tool, Teflon Tape, Pen or Pencil.
- Recommended Parts List for System Installation: 1" Male Thread Adapter X 4, 1" Shut Off Valve X 3.
Usage Features:
- Self-Installation: The manual provides detailed, step-by-step instructions for self-installation, covering everything from checking water flow direction to mounting the system and connecting plumbing.
- Valve Head Settings: The valve head has three primary settings:
- FILTER: This is the standard operational setting where water flows from the source, through the system, and out to the home plumbing for treatment.
- BACKWASH: This setting is used to remove impurities from the system and expand the media. Water flows out of a designated valve port to the drain. It is recommended every 7-10 days or as needed, running for 15 minutes, followed by a Fast Rinse cycle.
- FAST RINSE: Used immediately after the Backwash cycle, this setting forces the media to settle back down into the tank. Water flows out of a designated valve port to the drain. It is recommended to run for 5 minutes after a Backwash cycle.
- Bypass Installation (Recommended): Although not required, installing a bypass is highly recommended to ensure no downtime for water usage during repairs or system replacement.
- Water Flow Direction: The system can accommodate both left-to-right and right-to-left water flow directions, with instructions for reassembling the mounting bracket if needed.
- Pre-filter Placement: The pre-filter should always be placed before the main treatment system for maximum effectiveness and to lengthen the system's life.
Maintenance Features:
- Pre-filter Replacement: The Stage 1 pre-filter should be changed at least every 4-6 months, or more frequently in areas with poor water quality. A label on the filter cartridge indicates the recommended duration of use.
- Backwash and Fast Rinse Cycles: Regular backwash (15 minutes) and fast rinse (5 minutes) cycles are recommended at least once a week to maintain system performance and expand/settle the media.
- Housing Maintenance: Instructions are provided for safely removing and cleaning the filter housing during filter replacement. Users are cautioned against using chemicals to wash the housing.
- O-ring Inspection: Users are advised to check the o-ring for cracks or damage during filter replacement and replace it if necessary.
- System Startup after Maintenance: Steps include turning on the main water supply, checking for leaks, and running the nearest faucet for 10 minutes to release trapped air or carbon fines.
- Extended Warranty: Registering the product within 60 days of purchase extends the warranty to 5 years, encouraging regular maintenance and support.
- Subscribe and Save Program: Aquasure offers a subscription program for replacement pleated sediment filters, providing discounts and scheduled deliveries to simplify filter replacement.
Need help?
General
To Next Page
