E-20
AMP device mode
The AMP device mode button configures
the remote to control the Solo. Pressing
this button does not affect the currently
selected input on the Solo.
The functionality of the Solo is context
sensitive for the internal sources and is
described in the following table.
2
Toggles Solo power between
standby and powered on.
1
Open/close disc tray.
0…9
Searches for and plays the
track corresponding to the
key pressed when playing
a CD.
SYNC
Lipsync. Delays may be
introduced into the video
signal by video processing
which causes a mismatch
between the audio and
video timing. You will notice
this by speech sound being
out of synchronization with
the lip movements in the
video. To compensate for
this, you can adjust the lip
sync delay. Press the sync
button and use the
<
and
>
navigation buttons. Press
again to exit the lipsync trim
menu.
INFO
Info cycles through the
information displayed on the
lower left portion of the front
panel display
7
Rewind CD, DVD or BD.
8
Fast Forward CD, DVD or BD.
9
Skip back to the beginning
of the current/previous track
on CD, DVD or BD.
:
Skip forward to the
beginning of the next track
on CD, DVD or BD.
<
Stop playback on CD, DVD
or BD.
4
Play content on CD, DVD
or BD.
;
Pause playback on CD, DVD
or BD.
MENU Disc menu.
POP UP
Activates BD pop up menu, if
available.
RTN
Return from menu on BD/
DVD menus.
AUDIO
Selects between the
available audio tracks on a
BD/DVD
Navigate the files and menus
on the screen. OK selects the
highlighted file or enters the
highlighted menus on the
screen - equivalent to ‘Enter’
or ‘Select’ on some remote
control.
AMP+'
Power on from standby
AMP+,
Standby from Power on
AMP+>
Changes the picture
resolution
Returns navigation to the top
level of the menu (‘Home’).
Toggles the mute function of
the Solo
MODE
Cycles through the available
surround and downmix
modes
DISP
Cycles through the front
panel display’s brightness
options
Increase/decrease amplifier
volume
AMP Resets remote to AMP mode
SUBT
Cycles through subtitle
options, if available on DVD
or BD
RED Red button for BD
GREEN Green button for BD
YELLOW Yellow button for BD
BLUE Blue button for BD
RADIO Internal FM/DAB tuner input
BT Internal Bluetooth input
MEDIA Network, USB media input
DISC Internal disc input
AV AV HDMI input
SAT Satellite HDMI input
PVR PVR HDMI input
GAME Game console HDMI input
LINE Phono plug analogue input
AUX 3.5mm plug analogue input
STB
STB digital coaxial audio
input
TV TV optical audio output
SAT device mode
The SAT device mode button selects SAT
as the source. If configured to work with
your satellite reciever, the Solo remote can
subsequently control the device.
2
Toggles power between
standby and on.
0…9
Functions as original remote
number key – usually for
channel selection.
INFO
Display INFO or OSD (On
Screen Display) function, if
available.
7
Rewind
8
Fast forward
9
Channel down
:
Channel up
<
Stop playback
4
Play content
;
Pause content
Record
MENU Menu
Navigate setup and
programme selection menus.
OK confirms a selection
(equivalent to ‘Enter’ or ‘Select’
on some remotes).
Returns navigation to the top
level of the menu (‘Home’).
RTN Back
AMP Resets remote to AMP mode
RED RED button for Satellite
GREEN GREEN button for Satellite
YELLOW YELLOW button for Satellite
BLUE BLUE button for Satellite
Bluetooth commands
The Bluetooth audio input is selected by
pressing BT in AMP device mode on the
remote control. When connected to an
audio streaming device, the keys below
are used to navigate music tracks.
9/:
Selects the previous/next
track in the current playlist.
4
Play current track.
<
Pause current track.
Network media /USB commands
When using the network client, the keys
below are used to navigate music files in
AMP device mode.
Navigates the files on
screen. OK selects/plays the
highlighted file.
9/:
Selects the previous/next
track in the current playlist.
4
Play current track.
;
Pause current track.
<
Stops playback.
Returns navigation to the top
level of the network client
menus (‘Home’).
To Next Page
Loading...
