Ariens Sno-Thro Platinum SHO 24 User Manual (English)

Other manuals for Ariens Sno-Thro Platinum SHO 24

Questions and Answers:

G
george32Aug 21, 2025
How to start my Ariens Sno-Thro Platinum SHO 24 Snow Blower when the engine won't start?
- B
  Beth ClarkAug 21, 2025
  If your Ariens Snow Blower engine won't start, there are several possible causes. First, make sure the engine key is in the run position. Next, check that the choke is on, and the fuel valve is open. Ensure the fuel tank isn't empty and that the engine is primed if it's cold (press the primer bulb three times). If the engine is flooded, turn the choke control knob to the off position and try starting again. If these steps don't work, the ignition switch starter circuit may not be functioning, or the engine itself could be faulty, requiring a visit to your dealer or an authorized service center. Also, check for disconnected spark plug wire or faulty spark plug. Another reason may be build up of dirt and residue around governor / carburetor.
V
Vanessa PadillaAug 25, 2025
Why is my Ariens Sno-Thro Platinum SHO 24 not throwing snow effectively?
- J
  Jose LopezAug 25, 2025
  If your Ariens Snow Blower isn't throwing snow well, several issues could be the cause. Ice or debris may be obstructing the auger, or the discharge chute might be clogged with snow. Stop the engine, remove the key, and wait for moving parts to stop before clearing any obstructions. The impeller could be frozen in place, requiring you to move the unit to a warm place to thaw it. Also, the auger drive belt might be slipping, worn, or damaged, and needs adjustment or replacement.
T
Terry EspinozaAug 26, 2025
What should I check if my Ariens Sno-Thro Platinum SHO 24 Snow Blower won't move forward or backward?
- D
  David MorseAug 26, 2025
  If your Ariens Snow Blower isn't moving forward or in reverse, it could be due to several reasons. The friction disc might be worn and need replacement. The traction drive cable may not be adjusted correctly, so remove slack from the cable. Another possibility is a malfunctioning traction belt, which would need repair or replacement. Lastly, the speed selector might not be adjusted correctly, and you should adjust the speed selector.
J
James MooreAug 27, 2025
What causes continuous belt squealing in my Ariens Sno-Thro Platinum SHO 24?
- C
  Christopher MercerAug 27, 2025
  Continuous belt squealing in your Ariens Snow Blower can be caused by a couple of things. The impeller might be frozen, so try moving the unit to a warm area to thaw it. Alternatively, the attachment clutch may need adjustment.
B
Brenda HallAug 29, 2025
What to do if my Ariens Sno-Thro Platinum SHO 24 Snow Blower unit does not throw snow or throws it poorly?
- J
  jeffrey23Aug 29, 2025
  If your Ariens snow blower isn't throwing snow effectively, start by checking the shear bolts. Next, inspect the impeller for ice; if frozen, move the unit to a warm place to thaw. Also, check the auger for obstructions. Stop the engine, remove the key, and wait for moving parts to stop before removing any obstructions. Clear any snow clogging the discharge chute, remember to stop the engine, remove the key, wait for all moving parts to stop and for hot parts to cool, and use a clean-out tool, not your hands. A slipping, worn, or damaged auger drive belt may also be the cause.
R
Ryan OrtizAug 31, 2025
What to do if my Ariens Snow Blower unit runs briefly then stops?
- S
  Steven SwansonAug 31, 2025
  If your Ariens snow blower unit runs briefly then stops, it may be due to a build-up of fumes in the fuel tank creating too much pressure. Try slowly loosening the fuel tank cap.
J
Jennifer CuevasSep 1, 2025
What to do if my Ariens Sno-Thro Platinum SHO 24 Snow Blower unit does not drive forward or in reverse?
- K
  Kristin CobbSep 1, 2025
  If your Ariens snow blower does not drive forward or in reverse, the friction disc may be worn (replace the friction disc). Also, the traction drive cable might not be adjusted correctly (remove slack from the cable). Another reason could be that the traction belt is not functioning (repair or replace the traction drive belt). Finally, the speed selector might not be adjusted correctly (adjust the speed selector).
J
Joshua GrimesSep 3, 2025
What to do if my Ariens Sno-Thro Platinum SHO 24 Snow Blower engine stops while running?
- A
  Andrea HolmesSep 3, 2025
  If your Ariens Snow Blower engine stops, first check if the fuel tank is empty and refill if necessary. Ensure the fuel valve is open. Look for any obstructions in the auger or impeller, and if present, stop the engine, remove the key, wait for all moving parts to stop, and then remove the obstruction before restarting. Also, check for contaminated fuel and replace it with clean fuel. A faulty or dirty spark plug could also be the culprit, so replace or clean it. Lastly, a blocked fuel cap vent can cause the engine to stop, so try installing a new fuel cap.
D
Daniel BartonSep 5, 2025
Why does my Ariens Snow Blower engine start hard or run poorly?
- E
  Evelyn PerezSep 5, 2025
  If your Ariens Snow Blower engine starts hard or runs poorly, the fuel mixture may be too rich, so turn the choke control knob to the off position. Another cause could be a faulty, fouled, or incorrectly gapped spark plug; clean and correctly set the spark plug gap. Also, the fuel cap vent might be blocked, in which case you should install a new fuel cap.
B
Bill MorrisSep 6, 2025
Why does my Ariens Sno-Thro Platinum SHO 24 pull to one side?
- N
  Nathan MarquezSep 6, 2025
  If your Ariens Snow Blower pulls to the left or right, the skid shoes and scraper blade likely need adjustment. Adjust both the skid shoes and the scraper blade.

Ariens Sno-Thro Platinum SHO 24 Specifications

General

Clearing Width	24 inches
Intake Height	21 inches
Throwing Distance	Up to 50 feet
Speed Settings	6 forward / 2 reverse
Starting System	Electric start
Impeller Diameter	12 inches
Housing Material	Steel
Auger Material	Steel
Chute Rotation	200 degrees
Engine	254cc Ariens AX engine