Why front wheels lift when accelerating Arrma Motorized Toy Car?
If the front wheels of your Arrma Motorized Toy Car lift when accelerating, it's likely that the slipper clutch adjustment is too tight. Check that the slipper is set to the factory setting.
Overview of the ADX-10 model.
Overview of the Fury model.
Overview of the Granite model.
Overview of the Mojave model.
Overview of the Raider model.
Overview of the Vorteks model.
Required battery and charger for the RC model.
Required radio transmitter and receiver components.
Required AA batteries for the transmitter.
Requirement for PC and internet access for updates/info.
Safety guidelines for handling and using batteries to prevent damage or injury.
Identification of key components in the front section of the chassis.
Identification of key components in the rear section of the chassis.
Explanation of the buttons, switches, and indicators on the ATX100 transmitter.
How to adjust trim settings and bind the transmitter to the receiver.
Technical details including input voltage and BEC output for the ESC.
Transmitter functions for adjusting steering sensitivity and checking battery levels.
Default configurations for ESC channels, trims, and other settings.
Procedure for calibrating the ESC's throttle neutral position.
Understanding ESC status lights and how temperature protection works.
Features for battery protection and methods for tuning ESC performance.
Steps for installing the battery and first-time operation.
Techniques for driving, cornering, and essential checks after use.
List of necessary tools for performing upkeep on the RC vehicle.
A table listing common problems, their causes, and solutions.
Additional problem-solution pairings for vehicle issues.
A chart detailing maintenance tasks and recommended service intervals.
Steps to clean and check the chassis after each use.
Guide to inspecting, re-gluing, and fitting wheels and tires.
Procedure for tuning the slipper clutch for different driving conditions.
Method for correctly setting the mesh between the spur and pinion gears.
Instructions for cleaning, inspecting, and re-greasing driveshafts.
How to inspect the rear axle for wear and perform necessary checks.
Steps to remove and replace wheel bearings in the front of the vehicle.
Steps to remove and replace wheel bearings in the rear of the vehicle.
Specific factory settings for the Raider's front and rear suspension.
Specific factory settings for the ADX-10's front and rear suspension.
Specific factory settings for the Mojave's front and rear suspension.
Specific factory settings for the Vorteks' front and rear suspension.
Specific factory settings for the Granite's front and rear suspension.
How to modify ride height using included spacers.
Adjusting camber link length and steering arm length for wheel alignment.
Adjusting shock mounting and camber link position for suspension tuning.
Steps for removing front and rear shock absorbers.
Understanding spring effects and how to swap them.
Detailed guide on how to change the oil inside the shock absorbers.
Explanation of the gear chart and its impact on acceleration and top speed.
Steps for removing and replacing pinion and spur gears.
Guide on how to remove the motor for cleaning or upgrades.
How different differential oil weights affect vehicle handling characteristics.
Visual representation of all parts within the differential assembly.
Listing of part numbers for differential repair and maintenance kits.
How to gain access to the receiver for binding or upgrades.
How to access the steering assembly for adjustments or repairs.
Detailed instructions for removing the steering servo from the chassis.
Various optional shock absorber sets for different models.
Optional wheelie bar components and related parts.
Upgrade parts made of alloy for chassis and suspension components.
Alloy servo arms in different sizes for customization.
Blank fields for documenting Raider suspension adjustments.
Blank fields for documenting ADX-10 suspension adjustments.
Blank fields for documenting Mojave suspension adjustments.
Blank fields for documenting Vorteks suspension adjustments.
Blank fields for documenting Granite suspension adjustments.
General| Scale | 1/10 |
|---|---|
| Motor Type | Brushed |
| Suspension | Independent |
| Battery | 7.2V NiMH |
| Top Speed | 30+mph / 48+km/h |
| Shock Type | Oil-Filled |
| Body | Pre-Painted, Polycarbonate |
| Charger | Not Included |
| Radio | 2.4GHz |
| Battery Details | 7.2V NiMH (Not Included) |
To Next Page
