ascon ACK 20E - Page 57

55
Engineering & Physical Data ACK-E-2009
Component Data - Cooling Only (R22)
MODEL
INDOOR UNIT ACK 40E ACK 40E
OUTDOOR UNIT ALC 35C ALC 40C
INDOOR FAN
TYPE BLOWER WHEEL BLOWER WHEEL
QUANTITY 11
MATERIAL ASG 10% ASG 10%
DRIVE DIRECT DIRECT
DIAMETER
mm/in
462 / 18.18 462 / 18.18
LENGTH
mm/in
171 / 6.13 171 / 6.13
INDOOR FAN MOTOR
TYPE INDUCTION INDUCTION
QUANTITY 11
INDEX OF PROTECTION (IP) 20 20
OUTDOOR FAN
TYPE PROPELLER PROPELLER
QUANTITY 11
MATERIAL
GLASS REINFORCED ACRYL
STYRENE RESIN
GLASS REINFORCED ACRYL
STYRENE RESIN
DRIVE DIRECT DIRECT
DIAMETER
mm/in
609.6 / 24 609.6 / 24
OUTDOOR FAN
MOTOR
TYPE INDUCTION INDUCTION
QUANTITY 11
INDEX OF PROTECTION (IP) --
COMPRESSOR
TYPE SCROLL SCROLL
OIL TYPE MINERAL (Sontex 200 LT) MINERAL (Sontex 200 LT)
OIL AMOUNT
cm
3
/ fl .oz.
1240 / 43.6 1240 / 43.6
INDOOR COIL
TUBE
MATERIAL
SEAMLESS INNER GROOVED COPPER SEAMLESS INNER GROOVED COPPER
DIAMETER
mm/in
7 / 0.27 7 / 0.27
THICKNESS
mm/in
0.24 / 0.01 0.24 / 0.01
FIN
MATERIAL ALUMINIUM (SLIT FIN) ALUMINIUM (SLIT FIN)
THICKNESS
mm/in
0.11 / 0.004 0.11 / 0.004
FACE AREA
m
2
/ft
2
0.461 / 4.96 0.461 / 4.96
ROW 33
FIN PER INCH 20 20
OUTDOOR COIL
TUBE
MATERIAL SEAMLESS COPPER SEAMLESS COPPER
DIAMETER
mm/in
9.52 / 3/8 9.52 / 3/8
THICKNESS
mm/in
0.35 / 0.014 0.35 / 0.014
FIN
MATERIAL ALUMINIUM (SLIT FIN) ALUMINIUM (CORR. FIN)
THICKNESS
mm/in
0.127 / 0.005 0.127 / 0.005
FACE AREA
m
2
/ft
2
0.87 / 9.33 0.87 / 9.33
ROW 12
FIN PER INCH 16 14
AIR QUALITY FILTER
TYPE WASHABLE SARANET FILTER WASHABLE SARANET FILTER
QUANTITY
pc
11
SIZE
LENGTH
mm/in
576.0 / 22.7 576.0 / 22.7
WIDTH
mm/in
556.0 / 21.9 556.0 / 21.9
THICKNESS
mm/in
2 / 0.078 2 / 0.078
CASING
PANEL
MATERIAL
ABS ABS
FINISHING
N/A N/A
COLOUR
LIGHT GREY LIGHT GREY
INDOOR UNIT
MATERIAL
HOT DIP GALVANIZED STEEL HOT DIP GALVANIZED STEEL
FINISHING
WITH PE INSULATION WITH PE INSULATION
COLOUR
WITHOUT PAINT WITHOUT PAINT
OUTDOOR UNIT
MATERIAL
GALVANIZED MILD STEEL GALVANIZED MILD STEEL
FINISHING
POLYESTER POWDER POLYESTER POWDER
COLOUR
LIGHT GREY LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
07-General data_A.indd 5507-General data_A.indd 55 4/6/2009 11:13:13 AM4/6/2009 11:13:13 AM