ASKAYNAK 201 TIG PFC - User Manual

Questions and Answers

S
Scott GuzmanAug 18, 2025
Why is my ASKAYNAK 201 TIG PFC not working; no output, and the fan isn't running?
- M
  Michael McmahonAug 18, 2025
  If your ASKAYNAK Welding System isn't working, has no output, and the fan isn't running, here's what to check: * **No mains power:** Check the voltage of the phases entering the machine and reconnect the phases if necessary. * **Defective mains input cable:** Replace the cable if it's damaged. * **Defective on/off switch:** Replace the switch. If you need assistance, contact the service. * **Defective input filter and/or power board:** Contact the service.
J
johnsmithAug 20, 2025
What to do if the arc is not stable and welding cannot be done properly with my ASKAYNAK 201 TIG PFC Welding System?
- B
  Brenda SilvaAug 21, 2025
  If you are experiencing an unstable arc and cannot weld properly with your ASKAYNAK Welding System, consider the following: * **Pole connections:** Ensure the poles are correctly connected and tightened. * **Voltage value:** Check that the mains voltage is 220 V and that an extension cable of the correct length and size is being used. Correct as necessary.
G
Gerald AshleyAug 23, 2025
How to fix no welding current output on ASKAYNAK Welding System?
- A
  Alicia SotoAug 23, 2025
  If there is no welding current output from your ASKAYNAK Welding System, check these items: * **Connections:** Ensure all cables are properly connected to the machine outputs. * **Welding cable:** Replace the welding cable if it's damaged. * **Work cable:** Check the work cable and reconnect it if it's loose or disconnected.
S
Stephanie GuerreroAug 26, 2025
Why does the welding arc start with difficulty or the electrode sticks to the work piece when using my ASKAYNAK 201 TIG PFC?
- J
  Jessica RandolphAug 26, 2025
  If the welding arc starts with difficulty or the electrode sticks to the work piece when using your ASKAYNAK Welding System, there could be a few reasons: * **Loose connections:** Check all connections to ensure they are secure. * **Dirty workpiece:** Make sure the workpiece surface is clean, and free from oil or excessive dust.
K
Katelyn TateAug 27, 2025
How to get enough penetration when welding with ASKAYNAK 201 TIG PFC Welding System?
- K
  Kathryn WilliamsAug 28, 2025
  If you're not getting enough penetration while welding with your ASKAYNAK Welding System, the welding current setting might be too low. Try increasing the welding current.
B
Brittany SanchezAug 30, 2025
What causes arc blow and how to prevent it with ASKAYNAK Welding System?
- J
  Jamie WilsonAug 30, 2025
  Arc blow in your ASKAYNAK Welding System can be caused by a few factors. Here's how to address them: * **Air ventilation:** If air ventilation is too strong, use a protective barrier to shield the welding area. * **Welding electrode:** Check the welding electrode for any issues. * **Magnetic field effect:** Try changing the welding direction to the opposite of the arc blow.
D
dawsonchristopherSep 1, 2025
What to do if my ASKAYNAK 201 TIG PFC is making strange sounds and emitting a strange smell?
- A
  Alexander LeeSep 1, 2025
  If your ASKAYNAK Welding System is making strange sounds and emitting a strange smell, it could indicate a problem with the cooling fan. Check the cooling fan and contact the service if necessary.
C
Cheryl FordSep 3, 2025
Why does my ASKAYNAK 201 TIG PFC vibrate?
- L
  Leah BenitezSep 4, 2025
  If your ASKAYNAK Welding System is vibrating, it might not be seated on a sound and flat surface. Place the machine on a strong and flat surface.
P
Pedro BrewerSep 6, 2025
What causes no gas flow in ASKAYNAK 201 TIG PFC Welding System during TIG welding?
- D
  Danielle BellSep 6, 2025
  If you're experiencing no gas flow during TIG welding with your ASKAYNAK Welding System: * **Cylinder:** Ensure the cylinder is open and not empty. Replace the cylinder if needed. * **Valve:** Clean the valve if it's clogged. Clean the valve if it's defective.
J
joseph50Sep 8, 2025
Why can't I adjust the welding current properly on my ASKAYNAK 201 TIG PFC Welding System?
- H
  haley23Sep 8, 2025
  If you cannot adjust the welding current properly on your ASKAYNAK Welding System, the current control potentiometer on the front panel might be defective or not working. Contact the service.