EasyManua.ls Logo

Asus P7H57D-V EVO - Asus;3 Rd Party UI Priority; OC Tuner; Start Auto Tuning; DRAM Timing Control

Asus P7H57D-V EVO
128 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
3-18 Chapter 3: BIOS setup
Chapter 3
3.5.14 DRAM Timing Control
The items in this menu allow you to set the DRAM timing control features.
The conguration options for some of the following items vary depending on the DIMMs
you install on the motherboard.
1st Information: 7-7-7-20-4-60-8-5-20
The values vary depending on your settings of the following sub-items:
DRAM CAS# Latency [Auto]
Conguration options: [Auto] [3 DRAM Clock] [4 DRAM Clock] – [10 DRAM Clock]
[11 DRAM Clock]
DRAM RAS# to CAS# Delay [Auto]
Conguration options: [Auto] [3 DRAM Clock] [4 DRAM Clock] – [14 DRAM Clock]
[15 DRAM Clock]
DRAM RAS# PRE Time [Auto]
Conguration options: [Auto] [3 DRAM Clock] [4 DRAM Clock] – [14 DRAM Clock]
[15 DRAM Clock]
DRAM RAS# ACT Time [Auto]
Conguration options: [Auto] [3 DRAM Clock] [4 DRAM Clock] – [30 DRAM Clock]
[31 DRAM Clock]
DRAM RAS# to RAS# Delay [Auto]
Conguration options: [Auto] [1 DRAM Clock] – [7 DRAM Clock]
DRAM REF Cycle Time [Auto]
Conguration options: [Auto] [48 DRAM Clock] [60 DRAM Clock] [72 DRAM Clock] [82
DRAM Clock] [88 DRAM Clock] [90 DRAM Clock] [100 DRAM Clock] [110 DRAM Clock]
[114 DRAM Clock] [118 DRAM Clock] [122 DRAM Clock] [126 DRAM Clock] [130 DRAM
Clock] [134 DRAM Clock] [138 DRAM Clock] [142 DRAM Clock] [150 DRAM Clock] [160
DRAM Clock] [170 DRAM Clock] [180 DRAM Clock] [190 DRAM Clock] [200 DRAM Clock]
3.5.11 ASUS/3rd Party UI Priority [ASUS Utility]
[ASUS Utility] Prioritizes the usage of ASUS utilities (ASUS EPU, TurboV EVO, etc.).
Other third-party OC utilities may not be full-functioned.
[3rd Party Utility] Prioritizes third-party OC utilities (IXTU, SetFS, etc.). ASUS utilities can’t be
launched.
3.5.12 OC Tuner [Turbo Prole]
OC Tuner automatically overclocks the frequency and voltage of CPU and DRAM. Choose
[Good Performance] or [Better Performance] as a stable setting for daily use. Choose [Turbo
Prole] as an advanced overclocking setting for special purposes.
Conguration options: [Good Performance] [Better Performance] [Turbo Prole]
When using the Clarkdale CPU, only Turbo Prole mode appears. Good Performance and
Better Performance modes are supported by Lynneld CPUs only.
3.5.13 Start auto tuning
Press <Enter> to start auto tuning. It takes around 5 minutes, and the system will reboot for
several times before nish. After auto tuning, the C-State feature will be disabled.

Table of Contents

Related product manuals