What to do if I cannot close the door of my Atag VA98211QT/A08?
If your Atag Dishwasher's door won't close, consider these points: * Ensure the baskets are correctly positioned horizontally. * Check that the dishes are not blocking the baskets from sliding properly into place.
Why is my Atag VA98211QT/A08 making a rattling sound?
If you're experiencing a rattling sound when dishwashing with your Atag Dishwasher, it could be due to: * Improperly placed dishes or spray arms not rotating. Check that the dishes are placed securely and spin the spray arms to ensure they can rotate freely.
Why are there spots or films on the dishes after using my Atag VA98211QT/A08?
Spots or films on dishes can be due to several reasons. The water softener might be leaking salt; ensure the salt compartment lid is properly tightened. Check that you have the correct water softener setting. Also, verify the rinse aid dosage setting is correct. If the salt compartment is empty, top it up with salt. If you're using 3-in-1 detergent, make sure the TAB setting is inactivated and that you've added salt and rinse aid. High temperatures and too much detergent can etch crystal, so wash crystal at a low temperature with less detergent.
Why are my dishes not clean after using the Atag VA98211QT/A08?
If your dishes aren't clean, several factors could be the cause. The spray arms may not be rotating because they are blocked, so remove and clean them. Old detergent loses its effectiveness, so avoid buying large packages. Also, ensure you are using the correct detergent dosage for your water hardness, as too much or too little can affect results. Select a higher temperature or a more powerful wash program. Check that dishes are loaded correctly, not covering each other, and that glasses are stable. Finally, make sure the filter is correctly fitted.
How to get rid of bad odour in my Atag VA98211QT/A08 Dishwasher?
If your Atag Dishwasher has a bad odour, here are a couple of things you can try: * Clean around the seals and in corners with a washing-up brush and low foaming cleaner. * If you've been using low temperature programs for a long time, run a program with a higher temperature about once a month.
What to do if water remains in the Atag Dishwasher after cycle?
If your Atag Dishwasher has water remaining after a cycle, try these steps: * Loosen the drainage hose where it connects to the sink unit's water trap to check for blockages. Ensure the cone-shaped part of the pipe is cut to an inner diameter of at least 14 mm. * Make sure the drainage hose is free from kinks and sharp bends. * Clean the coarse and fine filters. * Clean the drainage pump.
Why are my dishes not drying in my Atag VA98211QT/A08?
If your Atag Dishwasher leaves dishes not dry enough, here are some possible solutions: * Activate the Long dry option. * Ensure the dishwasher is fully loaded for optimal drying. * Top up the rinse aid or increase the rinse aid dosage. Check the sections Before washing for the first time and Settings for guidance. * If you are using 3-in-1/All-in-one detergent and the setting TAB (3-in-1/ All-in-one detergent) is activated, inactivate the setting TAB (3-in-1/ All-in-one detergent) and top up salt and rinse aid. * Once the program has finished, open the door a little.
What to do if the Atag Dishwasher does not start?
If your dishwasher doesn't start, make sure you press and hold the Start/Stop button until the display shows the door open symbol, indicating it's ready. Check that the door is properly closed, and that a fuse/circuit breaker hasn't tripped. Ensure the plug is correctly plugged into the wall socket and that the water tap is turned on. Also, verify there are no overflows or leaks. Finally, check that the Delayed start option hasn't been accidentally selected; press and hold Start/Stop for three seconds to cancel it.
General| Brand | Atag |
|---|---|
| Model | VA98211QT/A08 |
| Category | Dishwasher |
| Language | English |
To Next Page
