How to get the dishes dry enough in Atag VA98211QT Dishwasher?
If your dishes aren't drying properly, try activating the Long dry option. Make sure you fully load the dishwasher. Check that the rinse aid is topped up and the dosage is correctly set. If you're using 3-in-1 detergent, inactivate the TAB setting and add salt and rinse aid. Once the program has finished, open the door a little.
What to do if the Atag VA98211QT does not start?
If your dishwasher doesn't start, make sure you press and hold the Start/Stop button until the display shows the door open symbol, indicating it's ready. Check that the door is properly closed, and that a fuse/circuit breaker hasn't tripped. Ensure the plug is correctly plugged into the wall socket and that the water tap is turned on. Also, verify there are no overflows or leaks. Finally, check that the Delayed start option hasn't been accidentally selected; press and hold Start/Stop for three seconds to cancel it.
Why are my dishes not drying in my Atag VA98211QT Dishwasher?
If your Atag Dishwasher leaves dishes not dry enough, here are some possible solutions: * Activate the Long dry option. * Ensure the dishwasher is fully loaded for optimal drying. * Top up the rinse aid or increase the rinse aid dosage. Check the sections Before washing for the first time and Settings for guidance. * If you are using 3-in-1/All-in-one detergent and the setting TAB (3-in-1/ All-in-one detergent) is activated, inactivate the setting TAB (3-in-1/ All-in-one detergent) and top up salt and rinse aid. * Once the program has finished, open the door a little.
What to do if water remains in the Atag VA98211QT after cycle?
If your Atag Dishwasher has water remaining after a cycle, try these steps: * Loosen the drainage hose where it connects to the sink unit's water trap to check for blockages. Ensure the cone-shaped part of the pipe is cut to an inner diameter of at least 14 mm. * Make sure the drainage hose is free from kinks and sharp bends. * Clean the coarse and fine filters. * Clean the drainage pump.
How to get rid of bad odour in my Atag VA98211QT Dishwasher?
If your Atag Dishwasher has a bad odour, here are a couple of things you can try: * Clean around the seals and in corners with a washing-up brush and low foaming cleaner. * If you've been using low temperature programs for a long time, run a program with a higher temperature about once a month.
How to remove spots left after washing in Atag VA98211QT?
If you have spots left after washing, especially from lipstick or tea, try using a detergent with a bleaching agent.
How to fix an Atag VA98211QT Dishwasher that is not cleaning dishes?
If your Atag Dishwasher isn't cleaning dishes properly, here's what you can do: * Remove the spray arms and clean them to ensure they rotate freely. * Check your detergent's expiration date, as old detergent can be less effective. Avoid buying large packages of detergent. * Adjust your detergent dosage according to your water hardness. Too much or too little detergent can affect cleaning. * Select a higher temperature or a more powerful dishwashing program. * Make sure dishes are loaded correctly, avoiding overcrowding or blocking spray arms. Do not cover porcelain with large bowls or the like. Avoid placing very tall glasses in the corners of the baskets. * Ensure dishes are placed securely to prevent them from toppling over during the cycle. * Confirm the filter is correct...
How to fix rattling sound when dishwashing in Atag VA98211QT Dishwasher?
A rattling sound during dishwashing usually means the dishes aren't correctly placed or the spray arms can't rotate. Make sure the dishes are placed securely. Spin the spray arms to ensure they can rotate freely.
Why does my Atag VA98211QT leave a sticky film on dishes?
If your Atag Dishwasher has a sticky white/blue film on the dishes, it is likely due to: * Rinse aid dosage setting being too high. Reduce the amount. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.
Why are the touch buttons on my Atag VA98211QT Dishwasher not working?
If the touch buttons on your Atag Dishwasher aren't responding, try the following: * Wait a moment and try again if you've pressed the touch buttons too soon after opening the door. * Clean the touch buttons with a dry or slightly damp cloth to remove any dirt. * If a specific symbol appears on the display, ensure the door is opened wide enough until the display lights up. Alternatively, close the door, wait 30 seconds, and then open it again. * Check if the child lock (button lock) is activated.
General| Number of Place Settings | 14 |
|---|---|
| Half Load Option | Yes |
| Child Lock | Yes |
| Water Consumption | 9.5 L |
| Programs | 8 |
| Delay Start | Yes |
To Next Page
