What to do if the monitor does not display when switching ports on ATEN CS82U?
If your ATEN Switch monitor doesn't display when switching ports, especially during the initial installation, switch ports again and allow two or more seconds for the PC's EDID to pass to the monitor. If the PC’s EDID has not passed through, use the [d] hotkey to invoke Video DynaSync or switch to another PC to reconnect the switch.
Why can't I switch ATEN CS82U ports by pressing [Scroll Lock] twice?
If you cannot switch ports on your ATEN Switch by pressing [Scroll Lock] twice, it might be that your keyboard is incompatible with Scroll Lock invocation. Switch to the Alternate HSM invocation keys.
What to do if the ATEN Switch monitor doesn't display after hot plugged KVM cable?
If your ATEN Switch monitor doesn't display after hot-plugging the KVM cable set, it could be due to incompatibility between some graphics cards and cable set hot-plugging. Power off all devices, including the switch, confirm all KVM cables are properly connected, then power on the switch and the computers.
Why is my ATEN CS82U Switch behaving erratically?
If your ATEN Switch exhibits erratic behavior, it might not be receiving enough power. Try using a DC 5 V power adapter, or if you're already using one, ensure it matches the system specifications, is properly plugged in, and is functioning correctly. Also, the keyboard and/or mouse may need a reset. Unplug the cables from the console ports and plug them back in. Check the cable from the switch to the computer to ensure it's properly connected. Finally, the KVM switch may need a reset: power off all devices, including the KVM switch, wait five seconds, and then power everything back up.
How to fix ATEN CS82U Switch when USB devices are not responding?
If USB devices are not responding on your ATEN Switch, try resetting the USB ports. Unplug the device’s USB cable from the USB port on the switch’s rear panel, and then plug it back in. Also, use the USB Reset hotkey combination to reset the USB ports.
Lists the key features and capabilities of the CS82U / CS84U KVM switch.
Lists the supported operating systems for the CS82U / CS84U KVM switch.
Provides step-by-step instructions for connecting the KVM switch to computers.
A visual guide illustrating how to connect the KVM switch, console, and computers.
Explains how to select computer ports using the front panel pushbuttons.
Introduces hotkey functions for controlling the KVM switch from the keyboard.
Explains how to enter Hotkey Setting Mode (HSM) to configure switch settings.
Details how to enable or disable the mouse port-switching function.
Provides instructions on how to run the firmware upgrade utility and navigate its screens.
Describes the screen that appears upon successful completion of the firmware upgrade.
Provides troubleshooting steps if the firmware upgrade process fails.
Lists essential safety precautions for installing and operating the KVM switch.
Lists detailed technical specifications for the CS82U and CS84U KVM switches.
Provides solutions for common operational problems and symptoms.
Lists the default factory settings for all hotkey functions.
General| DC-in jack | Yes |
|---|---|
| Console ports | PS/2, USB A, VGA (D-Sub) |
| USB connector type | USB Type-A |
| Number of computers controlled | 2 |
| Built-in display | No |
| Product color | Black, Light grey |
| Housing material | Metal |
| HD type | QXGA |
| Scan interval | 3, 5, 10, 20 s |
| Video bandwidth | 60 Hz |
| Maximum resolution | 2048 x 1536 pixels |
| Storage temperature (T-T) | -20 - 60 °C |
| Operating temperature (T-T) | 0 - 50 °C |
| Operating relative humidity (H-H) | 0 - 80 % |
| Power source | DC |
| Power consumption (typical) | 1.1 W |
| I/O ports | 2x SPHD-18 |
Weight and Dimensions| Depth | 140 mm |
|---|---|
| Width | 88 mm |
| Height | 55.5 mm |
| Weight | 540 g |
To Next Page
