EasyManuals Logo

Audio Technica ATH-SR50BT User Manual

Audio Technica ATH-SR50BT
22 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #8 background imageLoading...
Page #8 background image
7
Connecting via Bluetooth wireless technology
To connect the product to a Bluetooth device, the product needs to pair (register) with the device.
Pairing a Bluetooth device
Read the user manual for the Bluetooth device.
Place the Bluetooth device within 1 m (3.3') of the product to perform pairing correctly.
To confirm the progress of the pairing process, wear the product while performing this procedure and listen for the
confirmation tone.
1. Starting with the product turned o, slide the power switch to the “ON” position.
• The multi-indicator lamp will light in white, and then flash in white.
2. Use your Bluetooth device to begin the pairing process and search for the product.
When your Bluetooth device finds the product, “ATH-ANC900BT” will be displayed on the device.
• For information about using your Bluetooth device, refer to the device’s user manual.
• This product may be displayed as “ATH-ANC900BT”, “BLE_ATH-ANC900BT”, or both. If both are displayed, select
ATH-ANC900BT”. If only one is displayed, select that one.
3. Select “ATH-ANC900BT” to pair the product and your Bluetooth device.
• Some devices may ask for a passkey. In this case, enter “0000”. The passkey
may also be called a passcode, PIN code, PIN number, or password.
• The product sounds a confirmation tone when pairing is complete.
• Pairing a second device or more may take some time. In such cases, wait until
the multi-indicator lamp (p.15) indicates “pairing” .
About pairing
When connecting a new Bluetooth device, you need to pair it with the product. Once the Bluetooth device and the
product are paired, you do not need to pair them again. The product supports multi-pairing, in which a connection
history is saved.
However, in the following cases you will need to pair again even if the Bluetooth device was paired once:
If the product is deleted from the Bluetooth device’s connection history.
If the product is sent out for repair.
When switching to a Bluetooth device, you may not be able to
pair because the previously connected Bluetooth device cannot be
disconnected. In such cases, long touch (10 seconds) the upper and
center parts of the touch panel as shown in the figure. The product
will switch to the “searching for devices” state and you will be able
to pair with your desired Bluetooth device.
100%12
:
00
Bluetooth ON
ATH-ANC900BT

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Audio Technica ATH-SR50BT and is the answer not in the manual?

Audio Technica ATH-SR50BT Specifications

General IconGeneral
Impedance47 Ω
Driver typeDynamic
Driver unit45 mm
Ear couplingCircumaural
Headphone frequency5 - 40000 Hz
Microphone typeBuilt-in
Microphone frequency50 - 4000 Hz
Microphone sensitivity-44 dB
Microphone direction typeOmnidirectional
Cables includedUSB
Battery typeBuilt-in battery
Battery voltage3.7 V
Battery recharge time5.5 h
Continuous audio playback time28 h
Cable length0.3 m
Headset typeBinaural
Product typeHeadset
Product colorGray
Wearing styleHead-band
Volume controlTouch
Recommended usageCalls/Music
Operating temperature (T-T)5 - 40 °C
USB connectorMicro-USB
Frequency band2.402 - 2.48 GHz
Wireless range10 m
6.35 mm connectorNo
Bluetooth version5.0
Bluetooth profilesA2DP, AVRCP, HFP, HSP
Connectivity technologyWireless
Package depth225 mm
Package width252 mm
Package weight700 g
Weight and Dimensions IconWeight and Dimensions
Weight262 g

Related product manuals