Audiovox Jensen Power JPA260 User Manual

JPA260/JPA285
Amplifier Installation
& Operation Manual
JPA260/JPA285
Manual de Instalación y Operación
JPA260/JPA285
Manual de Installation et Operation
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Indicators and Controls . . . . . . . . . . . . . . . . . . 10
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Contenido
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Características . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Instalación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Cableado. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Indicadores y Controles . . . . . . . . . . . . . . . . . .10
Pruebas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Localización de Problemas. . . . . . . . . . . . . . . .13
Especificaciones . . . . . . . . . . . . . . . . . . . . . . . .14
Garantía. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Table des matières
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Dispositifs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Câblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Indicateurs et contrôles . . . . . . . . . . . . . . . . . . 10
Preuves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Localisations de problèmes. . . . . . . . . . . . . . . 13
Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Audiovox Jensen Power JPA260 Specifications

General

Channels	2
Frequency Response	20 Hz - 20 kHz
Signal-to-Noise Ratio	90 dB
RMS Power at 4 Ohms	60W x 2
RMS Power at 2 Ohms	90W x 2
Bridged RMS Power at 4 Ohms	180W x 1
Input Sensitivity	200 mV - 4 V
Fuse Rating	15 A

Summary

Introduction

Before You Begin

Advice before starting the installation and operation of the amplifier.

Warranty Service

Procedure for obtaining warranty service for the amplifier.

Features

Features

Detailed list of the amplifier's technical features and capabilities.

Installation

Installation Assistance

Contact information and resources for assistance during amplifier installation.

Supplies and Tools Needed

List of necessary tools and supplies for installing the amplifier.

Disconnect Battery

Location and Mounting

Guidance on selecting a suitable location and securely mounting the amplifier.

Routing Wires

Instructions and warnings regarding proper wire routing during installation.

Wiring

Charging System

Advice on upgrading the vehicle's charging system for amplifier installation.

Power Wiring (POWER)

Recommended wire gauges for power connections to the amplifier.

Power Terminal (+12V)

Remote Terminal (REM)

How to connect the remote turn-on lead from the receiver to the amplifier.

Ground Terminal (GND)

Instructions for making a proper ground connection for the amplifier.

Wiring (continued)

Speaker Wiring (SPEAKER)

Diagrams illustrating options for connecting speakers and observing polarity.

Pass-Thru RCA Outputs (OUTPUT)

How to use RCA outputs to connect multiple amplifiers.

Input Wiring

Low Level RCA Input (INPUT)

Preferred method for connecting audio signals using RCA cables.

High Level Input (HI-INPUT)

Alternative connection method using speaker outputs when RCA is unavailable.

Indicators and Controls

Power Indicator ()

Visual indicator showing when the amplifier is turned on.

Input Level Control (LEVEL)

How to match the radio's output to the amplifier's input for optimal performance.

Bass Boost (BASS EQ)

Adjustment for increasing low-frequency bass output.

Low Pass Filter (LPF)

High Pass Filter (HPF)

Limits low frequencies transmitted to speakers, useful for various setups.

Crossover (X-OVER)

Built-in filters for bi-amplifying, allowing selection of LPF, FULL, or HPF modes.

Standy-by Indicator (STAND-BY)

Thermal Protection

Amplifier shutdown due to overheating and safety precautions.

Overload and Short Circuit Protection

Amplifier shutdown due to electrical overload or short circuits.

Testing

Procedures to verify correct wiring and operation after installation.

Troubleshooting

Power Issues

Diagnosing problems related to the amplifier not turning on or lacking power.

Audio Quality Issues

Addressing distorted sound, engine noise, and sensitive volume controls.

Protection Circuitry Activation

Understanding and resolving issues related to thermal, overload, and low impedance protection.

Performance Issues

Troubleshooting poor bass response and speaker connection problems.

Testing and Verification

Procedures to verify correct wiring and proper operation after installation.

Specifications

CEA Power Ratings

Detailed power output specifications for JPA260 and JPA285 models.

General Specifications

Other general technical specifications including input sensitivity and crossover details.

12-Month Limited Warranty