Audiovox Pursuit PRO 9246FT User Manual

PRE-INSTALLATION NOTES:
PASSIVE / ACTIVE DOOR LOCK SELECTION: DIP SWITCH #1
This feature will only affect the operation of the system if the passive arming feature is selected.
When active door lock is selected, the doors will only lock when the transmitter button is pressed. When the alarm is
allowed to arm passively, at the end of the 30 second arming cycle, the doors
will not will not
will not will not
will not automatically lock. The system
is shipped in the active door lock mode, therefore, no modifications are required for this feature.
When passive door lock is selected, when the system is allowed to arm passively, at the end of the 30 second arming
cycle, the doors
will will
will will
will automatically lock. To program this feature, move dip switch number 1 to the on position.
AUTO LOCK / UNLOCK: DIP SWITCH #2
The system is shipped with this feature activated.
Any time the ignition key is turned to the off position, the doors will automatically unlock. Any time the ignition key is turned
to the on position, the doors will automatically lock when doors are closed.
To disable the auto lock / unlock feature, move dip switch number 2 to the “off” position.
PASSIVE / ACTIVE ARMING SELECTION: DIP SWITCH #3
This alarm can be programmed to operate as either a “PASSIVE” or “ACTIVE” arming security system.
As a “Passive” alarm, the system will automatically arm itself approximately 30 seconds after the ignition key is turned
off, one door is opened, then all vehicle doors are closed, (arming is suspended until the last door is closed). This feature
protects the vehicle in the event you forget to arm the system using the keychain transmitter. The doors will operate
according to the position of dip switch number 1.
This system is shipped in the passive mode, therefore no modifications are required to make the system operate as
a “Passive” alarm.
As an “Active” alarm, the system can only be armed using the keychain transmitter. There will be no backup automatic
arming.
To make the system operate as an “Active” alarm, move dip switch number 3 to the off position.
INOPERATIVE: DIP SWITCH #4
CHANNEL 2 OUTPUT:
This system provides an on board 10 A relay to activate the factory installed trunk release solenoid.
CHANNEL 3 OUTPUT:
This system provides an additional hardwire remote output to control an assortment of optional upgrades.
This output is an independent channel from the transmitter, and is controlled by pressing both buttons on the transmitter
simultaneously. It is a low current ground pulse (300 mA maximum), and the duration or length of the pulse varies (this
output will provide a ground signal for as long as both buttons are held), making it a versatile feature. This output can
be used to control;
* Optional Remote Starter AS 9075
* Optional Window Roll Up AS 9153
Model PRO 9246FT
Installation Manual

Audiovox Pursuit PRO 9246FT Specifications

General

Brand	Audiovox
Model	Pursuit PRO 9246FT
Category	Car Alarm
Language	English

Summary

Pre-Installation Notes

Passive/Active Door Lock Selection (DIP Switch #1)

Configures automatic door locking based on passive or active arming mode via DIP switch 1.

Auto Lock/Unlock (DIP Switch #2)

Enables/disables automatic door locking/unlocking when ignition is turned on/off via DIP switch 2.

Passive/Active Arming Selection (DIP Switch #3)

Selects passive (automatic) or active (transmitter) arming mode via DIP switch 3.

Channel 2 Output: Trunk Release

On-board 10A relay for factory-installed trunk release solenoid.

Channel 3 Output: Auxiliary Control

Hardwire remote output for optional upgrades like remote starter or window roll-up.

Remote Entry Illumination

Entry Illumination Wiring

Connects dark green/white wire to door pin switch for entry lighting and alarm flash.

Dome Light Relay Source Wiring

Connect dark blue/white wire for illumination feature and passive arming.

+12 Volt Output When Disarmed

Provides +12V output when disarmed or ignition is on, used for passive system control.

Valet Switch Connection

Route grey/black connector from valet switch to alarm control module.

6-Pin Door Lock Output: Normal Operation

Details wiring for orange, blue/white, yellow, white, green, blue wires for door lock relays.

2-Step Unlock Feature

Unlocks driver door on first press, all doors on second press within 3 seconds.

Positive/Negative Trigger Jumper

Sets door trigger circuit polarity for ground or positive switched dome light circuits.

System Features and Outputs

Parking Light Flasher Output

Provides output to control an optional parking light flasher relay.

Starter Disable Output

Provides output to control an optional starter cut relay, immobilizing the vehicle when armed.

Transmitter Programming

Details programming channels 1, 2, and 3 for transmitter button assignments and system functions.

Installation Support Hotline

Provides toll-free number for technical assistance during installation.

Component Mounting and Wiring

Control Module Mounting

Mount inside passenger compartment, avoid engine compartment and electronic components.

Valet Switch Mounting

Mount in an accessible location, preferably concealed, drill 1/4" hole if needed.

Red/White Wire: +12V Constant Battery

Connect to a +12 VDC constant battery source.

Black Wire: Chassis Ground

Connect to a solid, metal part of the vehicle's chassis.

Yellow Wire: +12VDC Ignition Source

Connect to a source hot during ignition ON and START positions.

Wiring Details and Circuit Types

Orange Wire: 300mA Ground Output (Armed)

Connect to terminal 86 for optional starter cut relay.

White Wire: 300mA Parking Light Output

Connect to terminal 86 for optional parking lamp flasher relay.

Dark Green/Black Wire: Channel 3 Output

Low current (300mA) output for optional devices, latches to ground.

Dark Blue Wires: Channel 2 Output (Trunk Release)

NO/COMMON contacts for trunk release or other accessories, 10A max.

3-Wire Ground Switched Door Lock Circuits

Wiring instructions for ground switched door lock circuits.

3-Wire Positive Switched Door Lock Circuits

Details wiring for positive switched circuits using yellow and white wires.

Advanced Wiring and Installation

5-Wire Alternating Door Lock Circuits

Instructions for connecting to 5-wire alternating door lock circuits.

6-Pin Door Lock Output: 2-Step Operation

Connects unlock relay outputs for 2-step unlock operation.

2-Step Unlock Connector Wiring

Wiring for green/black (ground pulse) and red/black (+12V source) 2-step unlock.

Completing Installation: Antenna

Extend antenna wire to full length, route away from damage.

Completing Installation: Operation Check

Check options, explain system operation to customer.

Completing Installation: Wire Dressing

Wrap alarm wires in tubing or tape, secure with ties to prevent damage.