Automatic Technology Australia Securalift GDO 2v4 - Page 3

Your
Securalift
Automatic
Garage
Door
Opener
has many
features
which
you
will appreciate. The
components
and materials
used
in
this
Automatic
Opener are
of the
latest
technology
and highest
qualrty.
Below
are
listed
some
of
these
features
OPERATION
To
operate the door
simply
press
the
hand held
transmitter or
the wall
mounted
transmitter
or
optional
wall switch for
two seconds
and the
door
will automatically
open
or
close.
The
door can
be stopped
during
an opening
or closing
cycle
by
pressing
again. The next
actuation
will
move
the
door
in
the
opposite
direction.
CODE HOPPING
Every
time a transmission is
made
from
the Remote Transmitter
a
new
security
code is
generated.
The
number
of
possible
code
combinations
nms
into
the billions.
This greatly
enhances
security
of
the
system.
Code
'Grabbing'
is
made
a thing
ofthe
past.
ISS
(INTELLIGENT
SAFETY
oBSTRUCTTON
SYSTEM)
While the
door
is
doing a closing
cycle
and
if
it
should hit
an obstacle
or
be
restricted
in
scme manner,
it
will automatically
reverse.
The
amount
of
force
the door
should
encounter
before reversing,
is
automatic4lly
adjudted
by the
doors
control
system,.
during the initial
installation
of the automatic
door
opener. The
door also if restricted
whilst
opening
will stop. The
Safety
Obstruction Force
shou ld
be
checked
at least
once a month.
See
installation
manual for
instructions
SECURITY
CODE
STORE
The
Opener
uses state
of the art
technology in
storing
your
selected
Transmitter
Security
Code.
Up to
27
different
codes
can be
stored
in
the Openers memory
device.
To
store any code
simply
press
and
hold
the Code Store button on the
Opener and
press
the Transmitter
button twice.
Each
or all codes
can
be
deleted and changed
at any time.
The
codes can also be
stored
from
a
remote
location.
OVER
LOAD
INDICATOR
When
the
maximum
opening
and
closing
capacity of the
Opener is
exceeded the Courtesy Light
and
Overload
LED
will flash
to
indicate
that
an Overload has
occurred.
SER}'ICE
INDICATOR
The
Opener has
a Service indicator.
When
the Overload LED lights
up
continuously it means
that the opener
and
,or
garage
door
needs
a service.
AUTO
COURTESY LIGHT
The
Courtesy
Light
on the
Opener
comes on automatically
whenever
tle
door
is
activated
to do
an
opening or
closing
cycle.
The
Light
can also
be
switched
on
and off
without
operating the
door. This
is
done
by
pressing
the button
on the Hand Held
Transmitter
Wireless
Wall
Mounted
Transmitter
which
has
being
stored
as the light
code,
or by
pressing
the
light
button
on
the Wall
Switch
(optional).
The
light
will
stay m for
approximately
three
minutes
then
go
off.. This
time is
also adjustable.
CAS
(COLOUR
ASSISTED
SETTINGS)
To
make
the
installation
of
the
Automatic
Opener
more
user friendly
Automatic
Technology
Australia
developed
the
CAS
(Colour
Assisted
Settings)
system. This
unique
system
allows for
all the Open
and
Close
adjustments
and settings
to be colour
coordinated,
Red for
Close
and
Green for
Open.
The
colour
coordination make
its
easier
and
quicker
for
the user or
installer
to
complete
the
installation.
OPEN AND
CLOSE DRTVE
BUTTONS
Another
feature
developed
by
Automatic Technology
Australia
in
aiding in the rnstallation
of the
opener are
the Ope,
and
Close
Drive
Buttons. These
buttons
are
used to help
set the open
and
close
limit positions.
A quicker
sefring
time
and a more
precise
limit
position
can
be
achieved usrng
this
system.
INITIALISATION
The
Reset
button
on the
!
or
Opener is
used
to
initialise
or
re-initialise
the
obstruction
settings
and
door travel
counts.
See
installation
manual
for instructions.
AUTO
CLOSE
MODE
The
Opener
can be
programmed
to
automatically
close
after
an open
cycle. The
Auto
Close
time is
adjustable.
A Photo
Electric
Beam
must
be
installed
if
this mode
is
selected.
AUTO
RT]N
TIME
If
the Motor
is left
running
in
the
Opener for
any reason
the
Auto
Run
Time
will
tum the motor
off
after
thirty
seconds.
PHOTO
ELECTRIC
BEAM
(oPTroNAL)
v
The
Opener has
an input for
a
Photo
Electric
Beam
to
be connected for
extra
safety
p
rotection.
MANUAL
OPERATION
The
Opener is
equipped
with
a
unique Manual Disengaging
Device.
If
the
power
to
the
Opener is
disrupted for
any
reason
the door
can
be
put
into Manual
Mode
by
pulling
down
on the
string handle
on an angle
towards
the
door,
then
releasing.
This
will
allow
you
to
manually
open
or close
the door. To
re-engage
pull
the
string at
an angle
away from
the
door then
release.
Page I