EasyManua.ls Logo

Avid Technology VENUE S6L - User Manual

Avid Technology VENUE S6L
8 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
VENUE | S6L Stage I/O Rack Supports
— 1/28/19 9329-65894-00 REV A
This guide shows you how to attach the included rack ears to the following VENUE | S6L I/O units:
Stage 64
Stage 32
Stage 16
Local 16
• On all units, the ears can be installed on the front or the back of the rack depending on the desired orientation.
• Stage 64 instructions also show how to mount the rack into a flight case, furniture or other rack housing.
• Stage 16 instructions show how to configure the ears for rack mounting or to be used as handles.
© 2019 Avid Technology, Inc 9329-66011-00 REV A

Table of Contents

Other manuals for Avid Technology VENUE S6L

Preview: System Guide
System Guide432 pages
Preview: Installation Guide
Installation Guide86 pages
Preview: Handbook
Handbook40 pages

Questions and Answers

  • J
    John Anderson DDSNov 27, 2025
    What causes repeated failures on Avid Technology VENUE S6L Recording Equipment?
    • S
      scottcaitlinDec 1, 2025
      Repeated failures on your Avid Technology Recording Equipment can be caused by an incompatible plug-in, a corrupted data file or application software, or a hardware error. Check to make sure you are using the most current versions of all your plug-ins. If failures occur only when you try to use a certain plug-in, disable that plug-in and see if problems go away. Try re-installing plug-ins that are causing problems. Determine if a certain Show file causes the system to fail consistently. If so, delete that file and see if problems persist. Clear the console from the Options > System page and see if problems persist. If necessary, you can reinstall VENUE software by doing a System Update. If you suspect problems with the system hard drive, or the system software, you can do a complete restor...
  • T
    Terry PattonAug 23, 2025
    What to do if Stage I/O is not passing audio on Avid Technology Recording Equipment?
    • T
      Tiffany BurgessAug 23, 2025
      If the Stage I/O on your Avid Technology Recording Equipment isn't passing audio, the stage unit may need to be reset. See Resetting Hardware Components, or power-cycle the Stage 64. Alternatively, there might be a bad or missing connection to the E6L engine, another Stage unit, or to power. Check the audio network cable connecting the Stage unit to the E6L engine (or, if daisy-chained, to the nearest Stage unit) to ensure it's properly connected and undamaged. Also, verify the Stage unit has power.
  • D
    David ClayAug 25, 2025
    Why are one or more plug-ins unavailable on my Avid Technology Recording Equipment?
    • C
      chelseasloanAug 26, 2025
      One or more plug-ins may be unavailable on your Avid Technology Recording Equipment because a Show was loaded that references plug-ins which are unavailable on the current system. Install the plug-ins, if available, or remove or replace the plug-ins in the Show, or load a different Show file. Also, a plug-in might not be fully compatible and is causing failures. Check all plug-ins to ensure you are using the most recent versions. Go to Options > Plug-Ins and Click the plug-in to display the version number. Try disabling plug-ins one-by-one to see if doing so eliminates problems.
  • C
    Candace HinesAug 27, 2025
    How to fix a previously connected device that is unavailable on Avid Technology VENUE S6L?
    • S
      Stephanie JohnsonAug 27, 2025
      If a previously connected device is unavailable and grayed out on your Avid Technology Recording Equipment, it could be because the device is no longer present. Touch-and-hold (right-click) the device graphic in the Options > Devices page and choose Forget to dismiss warning dialogs. Another reason might be a bad or missing connection to the E6L engine. Check to make sure the cable connecting the device is properly connected and not damaged, and that the device is powered on.
  • J
    Jesse GregoryAug 27, 2025
    What does it mean when I see warning dialogs that one or more devices have failed on my Avid Technology VENUE S6L?
    • E
      Elizabeth HernandezAug 27, 2025
      If you're seeing warning dialogs that one or more devices have failed on your Avid Technology Recording Equipment, it could be due to a bad or missing connection. Check connections to other components. Another potential cause is that a device needs to be reset. Try resetting the device, and if that doesn't work, power cycle the device.
  • G
    Gary WalterSep 18, 2025
    What causes a 'Control Surface Module Lost' error on Avid Technology VENUE S6L?
    • S
      Sarah BrownSep 18, 2025
      If the Control Surface Module is lost on your Avid Technology Recording Equipment, it is due to a network error. See Restarting Your System.
  • B
    Barry WoodSep 15, 2025
    What does it mean when an unsupported HDX DSP configuration is detected on Avid Technology VENUE S6L Recording Equipment?
    • D
      David WoodsSep 15, 2025
      If an unsupported HDX DSP configuration is detected on your Avid Technology Recording Equipment, the HDX DSP card may be installed improperly. Make sure you have installed your HDX DSP card in the correct slot in the E6L engine.
  • T
    Thomas RiceSep 17, 2025
    Why is my Avid Technology VENUE S6L Recording Equipment shutting down due to 2 fan blocks not working?
    • L
      Lindsey FosterSep 17, 2025
      If 2 fan blocks in the Engine have stopped working, and your Engine will now shut down to prevent overheating on your Avid Technology Recording Equipment, all fans inside the E6L engine have failed. The E6L engine will not operate unless at least one fan block is operational. When possible, check the internal fan connections, and replace the fans if necessary.
  • M
    Marc PageSep 7, 2025
    What causes a 'Clock Lost' error on Avid Technology VENUE S6L Recording Equipment?
    • J
      Jason SnyderSep 7, 2025
      If you are experiencing a 'Clock Lost' error on your Avid Technology Recording Equipment, the systems might be connected in an unsupported clock configuration. Make sure the WCOut port on the MADI-192 MADI Option card is not connected.
  • M
    Mrs. Michelle BakerSep 4, 2025
    Why has a Fader Module, Channel Knob Module, or Master Live Module stopped working on my Avid Technology Recording Equipment?
    • J
      Joshua BerrySep 4, 2025
      If a Fader Module, Channel Knob Module, or Master Live Module has stopped working or lost connection on your Avid Technology Recording Equipment, it's likely due to a network error. See Restarting Your System.

Summary

VENUE Stage 64 Rack Mounting

Stage 64 Components

Lists components needed for mounting the Stage 64 rack ears.

Stage 64 Attaching Rack Ears

Details how to attach rack ears to the front or back of the Stage 64.

Stage 64 Mounting in a Case

Explains how to install the Stage 64 into a flight case or other enclosure.

VENUE Stage 32 Rack Mounting

Stage 32 Components

Lists components required for mounting Stage 32 rack ears.

Stage 32 Attaching Rack Ears

Provides instructions for attaching rack ears to the Stage 32 unit.

VENUE Stage 16 Rack Mounting & Handles

Stage 16 Configuring Rack Ears as Handles

Instructions for configuring Stage 16 rack ears to function as handles.

VENUE Local 16 Rack Mounting

Local 16 Components

Lists the components needed for mounting the Local 16 rack ears.

Local 16 Attaching Rack Ears

Details the process of attaching rack ears to the Local 16 unit.

Avid Technology VENUE S6L Specifications

General IconGeneral
TypeDigital Mixing System
EQ Bands4-band parametric EQ per channel
Bit Depth24-bit
Processing PowerMultiple DSP Engines
DynamicsCompressor
EffectsReverb, Delay, Modulation
I/OModular
ConnectivityEthernet
Sample Rate96 kHz
PluginsAAX DSP
Control SurfaceTouchscreen
SoftwareAvid VENUE Software

Related product manuals