Axel WOLF - Page 37

WOLF NETWORK CONFIGURATION IMPORT / EXPORT FILE
Axel Technology |
37
alarm will be generated.
45
ALARM_AUDIO_PEAK_THR_LOW=No_Inf_Limit
This parameter sets the Audio Peak
measurement value below which the parameter
becomes invalid and an alarm is generated.
No_Inf_Limit = control disabled
(see protocol)
46
ALARM_AUDIO_PEAK_THR_HIGH=+3.0dB
This parameter sets the Audio Peak
measurement value above which the parameter
becomes invalid and an alarm is generated.
No_Sup_Limit = control
disabled
(see protocol)
47
ALARM_AUDIO_RMS_THR_LOW=No_Inf_Limit
This parameter sets the Audio RMS
measurement value below which the parameter
becomes invalid and an alarm is generated.
No_Inf_Limit = control
disabled
(see protocol)
48
ALARM_AUDIO_RMS_THR_HIGH=-3.0dB
This parameter sets the Audio RMS
measurement value above which the parameter
becomes invalid and an alarm is generated.
No_Sup_Limit = control
disabled
(see protocol)
49
ALARM_AUDIO_AVG_RMS_THR_LOW=No_Inf_Limi
t
This parameter sets the Audio RMS Average
measurement value below which the parameter
becomes invalid and an alarm is generated.
No_Inf_Limit = control
disabled
(see protocol)
50
ALARM_AUDIO_AVG_RMS_THR_HIGH=-3.0dB
This parameter sets the Audio RMS Average
measurement value above which the parameter
becomes invalid and an alarm is generated.
No_Sup_Limit = control
disabled
(see protocol)
51
ALARM_AUDIO_AVG_PEAK_THR_LOW=No_Inf_Lim
it
This parameter sets the (average) Audio Peak
measurement value below which the parameter
becomes invalid and an alarm is generated.
No_Inf_Limit = control
disabled
(see protocol)
52
ALARM_AUDIO_AVG_PEAK_THR_HIGH=+3.0dB
This parameter sets the (average) Audio Peak
measurement value above which the parameter
becomes invalid and an alarm is generated.
No_Sup_Limit = control
disabled
(see protocol)
53
ALARM_MPX_1_PILOT_THR_LOW=-23.5dB
This parameter sets the stereophonic pilot
carrier (19Hz) measurement value at the MPX-
1 input. If the measurement is below the value
set, an alarm is generated.
54
ALARM_MPX_1_PILOT_THR_HIGH=-21.5dB
This parameter sets the stereophonic pilot
carrier (19Hz) measurement value at the MPX-
1 input. If the measurement is below the value
set, an alarm is generated.
55
ALARM_MPX_1_PILOT_PROT_THR=-45.0dB
This parameter sets the pilot protection
measurement value, i.e. the purity (presence or
absence of spurious and harmonic emissions,
disturbance…) around the 19Hz frequency or
the stereophonic pilot. The measurement is
taken at the MPX-1 input. If the measurement is
above the value set, an alarm is generated.
See the section on Pilot Protection
56
ALARM_MPX_1_RDS_THR_LOW=-28.5dB
This parameter sets the RDS data carrier (57
Hz) measurement value at the MPX-1 input. If
the measurement is below the value set, an
alarm is generated.
57
ALARM_MPX_1_RDS_THR_HIGH=-25.5dB
This parameter sets the RDS data carrier (57
Hz) measurement value at the MPX-1 input. If
the measurement is below the value set, an
alarm is generated.
58
ALARM_MPX_1_PEAK_DEV_THR_LOW=No_Inf_Lim
it
This parameter sets the peak deviation of the
MPX signal at the MPX-1 input. If the
measurement is below the value set, an alarm
is generated.
59
ALARM_MPX_1_PEAK_DEV_THR_HIGH=90KHz
This parameter sets the peak deviation of the
MPX signal at the MPX-1 input. If the
measurement is above the value set, an alarm
is generated.
60
ALARM_MPX_1_ITUB412_THR_LOW=No_Inf_Limi
t
This parameter sets the MPX Power (19Hz)
measurement value (expressed as
recommendations ITU BS 412) at the MPX-1
input. If the measurement is below the value
set, an alarm is generated.
61
ALARM_MPX_1_ITUB412_THR_HIGH=No_Sup_Lim
it
This parameter sets the MPX Power (19Hz)
measurement value (expressed as
recommendations ITU BS 412) at the MPX-1
input. If the measurement is above the value