Axel WOLF - Page 41

WOLF NETWORK CONFIGURATION IMPORT / EXPORT FILE
Axel Technology |
41
frequency of the internal FM tuner (Monitor-
RF).
[END_AUTOMATIC_MODE_PRESET]
[RDS_MASK_SETTINGS]
In this menu you can set the RDS service
parameters to compare them with those from
the RDS decoder. If what is actually decoded
does not tally with what is written below, alarms
may be generated (which can be enabled or
not).
107
TRAFFIC_ANNOUNCEMENT=On
TA status setting
See RDS protocol
108
TRAFFIC_PROGRAM=On
TA status setting
See RDS protocol
109
ALTERNATIVE_FREQUENCIES=On
Alternative Frequencies status setting
See RDS protocol
110
MUSIC_SPEECH=Music
M/S status setting
See RDS protocol
111
DECODER_IDENTIFICATION=Stereo_Static_Pt
y
DI status setting
See RDS protocol
112
PROGRAM_TYPE=News
Program Type status setting
See RDS protocol
113
PROGRAM_SERVICE_NAME="RTL "
PSN status setting
See RDS protocol
114
PROGRAM_IDENTIFICATION=5201
PI value setting
See RDS protocol
[END_RDS_MASK_SETTINGS]
[ALARM_GENERAL_MASK]
This menu allows you decide whether or not to
mask the presence of certain conditions or
errors detected by the Wolf.
115
MAIN_SILENCE=On
This parameter is used to display (or not) the
silence setting at the main input.
See parameter 38
116
MAIN_AUDIO_PEAK=On
This parameter is used to display (or not)
Audio Peak errors at the main input.
117
MAIN_AUDIO_AVG_PEAK=On
This parameter is used to display (or not)
Audio Average Peak errors at the main input
118
MAIN_AUDIO_RMS=On
This parameter is used to display (or not)
Audio RMS errors at the main input.
119
MAIN_AUDIO_AVG_RMS=On
This parameter is used to display (or not)
Audio Average RMS errors at the main input.
120
MPX1_PILOT=On
This parameter is used to display (or not) the
stereophonic pilot (19 Hz) at the MPX-1 input.
121
MPX1_RDS=On
This parameter is used to display (or not) the
RDs service (57 Hz) at the MPX-1 input.
122
MPX1_DEVIATION=On
This parameter is used to display (or not) the
“Excess or No deviation” error at the MPX-1
input.
123
MPX1_ITUBS412=Off
This parameter is used to display (or not) the
ITU-R BS412 error at the MPX-1 input.
124
MPX1_PILOT_PROTECTION=Off
This parameter is used to display (or not) the
Pilot Protection control error at the MPX-1
input.
125
MPX1_DECODER_SILENCE=Off
This parameter is used to display (or not) the
decoded audio control (intended as the
presence of silence) from the MPX-1 input.
126
MPX1_DECODER_RMS=Off
This parameter is used to display (or not) the
decoded audio control (expressed as RMS)
from the MPX-1 input.
127
MPX2_PILOT=On
This parameter is used to display (or not) the
stereophonic pilot (19 Hz) at the MPX-2 input.
128
MPX2_RDS=On
This parameter is used to display (or not) the
RDs service (57 Hz) at the MPX-2 input.
129
MPX2_DEVIATION=On
This parameter is used to display (or not)
“Excess or No deviation” errors at the MPX-2
input.
130
MPX2_ITUBS412=Off
This parameter is used to display (or not) ITU-
R BS412 errors at the MPX-2 input.
131
MPX2_PILOT_PROTECTION=On
This parameter is used to display (or not) Pilot
Protection control errors at the MPX-2 input.
132
MPX2_DECODER_SILENCE=On
This parameter is used to display (or not) the
decoded audio control (intended as the
presence of silence) from the MPX-2 input.