Axel WOLF - Page 42

WOLF NETWORK CONFIGURATION IMPORT / EXPORT FILE
Axel Technology |
42
133
MPX2_DECODER_RMS=On
This parameter is used to display (or not) the
decoded audio control (expressed as RMS)
from the MPX-2 input.
134
FM_MPX_PILOT=On
This parameter is used to display (or not) the
stereophonic pilot (19 Hz) at the FM input
(Monitor-RF).
135
FM_MPX_RDS=On
This parameter is used to display (or not) the
RDS service (57 Hz) at the FM input (Monitor-
RF).
136
FM_MPX_DEVIATION=On
This parameter is used to display (or not)
“Excess or No deviation” errors at the FM input
(Monitor-RF).
137
FM_MPX_ITUBS412=On
This parameter is used to display (or not) ITU-
R BS412 errors at the FM input (Monitor-RF).
138
FM_MPX_PILOT_PROTECTION=On
This parameter is used to display (or not) Pilot
Protection control errors at the FM input
(Monitor-RF).
139
FM_MPX_DECODER_SILENCE=On
This parameter is used to display (or not) the
decoded audio control (intended as the
presence of silence) from the FM input
(Monitor-RF).
140
FM_MPX_DECODER_RMS=On
This parameter is used to display (or not) the
decoded audio control (expressed as RMS)
from the FM input (Monitor-RF).
141
MPX0_PILOT=On
This parameter is used to display (or not) the
stereophonic pilot (19 Hz) at the MPX-0 input.
142
MPX0_RDS=On
This parameter is used to display (or not) the
RDs service (57 Hz) at the MPX-0 input.
143
MPX0_DEVIATION=On
This parameter is used to display (or not)
“Excess or No deviation” errors at the MPX-0
input.
144
MPX0_ITUBS412=Off
This parameter is used to display (or not) ITU-
R BS412 errors at the MPX-0 input.
145
MPX0_PILOT_PROTECTION=On
This parameter is used to display (or not) Pilot
Protection control errors at the MPX-0 input.
146
MPX0_DECODER_SILENCE=On
This parameter is used to display (or not) the
decoded audio control (intended as the
presence of silence) from the MPX-0 input.
147
MPX0_DECODER_PEAK=On
This parameter is used to display (or not) the
Peak decoded audio control from the MPX-0
input.
148
RDS_QUALITY=Off
Alarm generation and display re. quality of the
RDS service (expressed as a %)
Inherent to the MAIN input
149
RDS_PI=On
Alarm generation and display re. PI control. If
this does not match the setting, an alarm is
generated.
Inherent to the MAIN input
150
RDS_DI=On
Alarm generation and display re. DI control. If
this does not match the setting, an alarm is
generated
151
RDS_PTY=On
Alarm generation and display re. Program Type
control. If this does not match the setting, an
alarm is generated.
Inherent to the MAIN input
152
RDS_TP=On
Alarm generation and display re. Traffic
Program status control. If this does not match
the setting, an alarm is generated
Inherent to the MAIN input
153
RDS_MS=On
Alarm generation and display re. Music/Speech
status control. If this does not match the setting,
an alarm is generated
Inherent to the MAIN input
154
RDS_PS=On
Alarm generation and display re. Program
Service status control. If this does not match
the setting, an alarm is generated.
Inherent to the MAIN input
155
RDS_TMC=Off
Alarm generation and display re. the presence
of traffic information (TMC).
Inherent to the MAIN input
156
RDS_EON=Off
Alarm generation and display re. the presence
of the Enhance Other Network control.
Inherent to the MAIN input
157
RDS_AF=On
Alarm generation and display re. the presence
of the Alternative Frequencies List control.
Inherent to the MAIN input
158
FM_RDS_QUALITY=Off
Alarm and generation display re. quality of the
RDS service (expressed as a %)
Inherent to the FM input (Monitor-RF)
159
FM_RDS_PI=On
Alarm generation and display re. PI control. If
this does not match the setting, an alarm is
generated
Inherent to the FM input (Monitor-RF)
160
FM_RDS_PTY=Off
Alarm generation and display re. Program Type
control. If this does not match the setting, an
Inherent to the FM input (Monitor-RF)