Azden 1201URX/VM - User Manual

User’s Guide
1201URX/AB • 1201URX/VM • 1201URX/Si
1201BT • 1201XT
ENHANCED BROADCAST PERFORMANCE
UHF WIRELESS SYSTEM
1201URX/AB - 1201URX/Si - 1201URX/VM
RF Carrier Frequency Range 188 steps ~ 638.125 - 661.875 MHz
MicroComputer Controlled PLL Synth.
Noise Reduction Expander (THAT)
Effective Operating Range 200 - 300 ft ~ 60 - 100m
Frequency Response 50 - 15kHz (± 1.5dB)
RF Sensitivity (12dB SINAD) 1.2μV
Adjacent Channel Selectivity > 70dB (± 250kHz)
Image Rejection > 93dB
IF Rejection > 93dB
Audio THD < 0.8%
Audio Output 40dBm ± 40kHz Deviation (-20dBm ± 40kHz Deviation for 1201URX\Si)
Output Impedance 600Ω (300Ω for 1201URX\Si)
Signal/Noise Ratio > 62dB (± 5kHz Deviation) “A” Weighted
Power Requirements 11 - 15V DC @ 220mA (10 - 17V DC @ 200mA for 1201URX\Si)
Dimensions 68W x 84H x 18D mm- 1201URX/Si insertion
93W x 119H x 49D mm - 1201URX/AB
82W x 150H x 60D mm - 1201URX/VM
Operating Temperature Range -50
0
- +122
0
F ~ -10
0
- +50
0
C
Weight 8.8 ounces ~ 250g for 1201URX/Si
15.87ounces ~ 450g for 1201URX/AB
26.45ounces ~ 750g for 1201URX/VM
1201BT
Output Power 30mW
Max Modulation Sensitivity -4dBm
MIC Level / Imped. -56dBm (± 5kHz Deviation)
Power Requirements 3V DC (2 “AA” Alkaline) @ < 150mA
Dimensions 2.48 (W) x 3.86 (H) x 1.12 (D) inches
63 (W) x 98 (H) x 28.5 (D) mm
Weight w/Battery 6.35 ounces ~ 180g
1201XT
Output Power 30mW
Max Modulation Sensitivity +20dBM ~ 0dBm
MIC Level / Imped. (Dynamic) -60dBm / 2.2kΩ (± 5kHz Dev.)
Phantom Power 48V ±2V @ 2mA
Power Requirements 3V DC (2 “AA” Alkaline) @ < 180mA - 290 mA w/Phantom Power ON
Dimensions 1.57 (W) x 4.49 (H) x 1.57 (D) inches
40 (W) x 114 (H) x 40 (D) mm
Weight w/Battery 6.35 ounces ~ 180g
Due to constant improvements, specications are subject to change without notice.
Licensing
Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license depends largely on the user’s classication, applica-
tion and frequency. Contact the appropriate agency (FCC in the USA) for further information.
SPECIFICATIONS
Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010
tel - 516.328.7500 • fax - 516.328.7506 • email - sales@azdencorp.com
© 2010 Azden Corporation Printed in USA P1030-02

Summary

Specifications

Effective Operating Range

Indicates the reliable distance for signal transmission between components.

Power Requirements

Details the voltage and current needed for operation.

1201 BT Power Requirements

Details the voltage and current needed for the 1201BT.

1201 XT Power Requirements

Details the voltage and current needed for the 1201XT.

Introduction

Using the 1201 XT Transmitter Controls and Display

MIC Connector;Locking Ring

Details the microphone input, wiring, and securing mechanism.

Receiver Setup;Use - 1201 URX;AB or 1201 URX;VM

Attaching antennas

Instructions for attaching the high-gain antennas to the receiver.

Connecting the Output cable

Details how to connect the receiver's output to a camera.

Setting the Receiving Frequency

Explains how to set the receiver's operating frequency.

LCD Display

Explains what information is shown on the receiver's display.

Using the 1201 Transmitter Controls and Display

Power

Describes how to turn the 1201BT transmitter ON and OFF.

MIC

Details the microphone input connector and wiring for various mics.

Input Level Adjustment

Explains how to adjust the microphone input gain.

Setting the Transmitting Frequency on the 1201 BT

Receiver Setup;Use - 1201 URX;AB or 1201 URX;VM

Mode #1 (GR)

Describes how to select the Group for frequency combinations.

The 1201 URX;Si

Mode #2 (CH)

Explains how to change the channel/frequency within a selected group.

Azden 1201URX/VM Specifications

General

Type	UHF Receiver
Modulation	FM
Audio Frequency Response	50 Hz - 15 kHz
Operating Range	Up to 300 ft (90 m) line-of-sight
Output Connectors	3.5 mm mini-jack
Power Supply	2 x AA batteries
Battery Life	Approximately 8 hours