Azden 1201XT - User Manual

User’s Guide
1201URX/AB • 1201URX/VM • 1201URX/Si
1201BT • 1201XT
ENHANCED BROADCAST PERFORMANCE
UHF WIRELESS SYSTEM
1201URX/AB - 1201URX/Si - 1201URX/VM
RF Carrier Frequency Range 188 steps ~ 638.125 - 661.875 MHz
MicroComputer Controlled PLL Synth.
Noise Reduction Expander (THAT)
Effective Operating Range 200 - 300 ft ~ 60 - 100m
Frequency Response 50 - 15kHz (± 1.5dB)
RF Sensitivity (12dB SINAD) 1.2μV
Adjacent Channel Selectivity > 70dB (± 250kHz)
Image Rejection > 93dB
IF Rejection > 93dB
Audio THD < 0.8%
Audio Output 40dBm ± 40kHz Deviation (-20dBm ± 40kHz Deviation for 1201URX\Si)
Output Impedance 600Ω (300Ω for 1201URX\Si)
Signal/Noise Ratio > 62dB (± 5kHz Deviation) “A” Weighted
Power Requirements 11 - 15V DC @ 220mA (10 - 17V DC @ 200mA for 1201URX\Si)
Dimensions 68W x 84H x 18D mm- 1201URX/Si insertion
93W x 119H x 49D mm - 1201URX/AB
82W x 150H x 60D mm - 1201URX/VM
Operating Temperature Range -50
0
- +122
0
F ~ -10
0
- +50
0
C
Weight 8.8 ounces ~ 250g for 1201URX/Si
15.87ounces ~ 450g for 1201URX/AB
26.45ounces ~ 750g for 1201URX/VM
1201BT
Output Power 30mW
Max Modulation Sensitivity -4dBm
MIC Level / Imped. -56dBm (± 5kHz Deviation)
Power Requirements 3V DC (2 “AA” Alkaline) @ < 150mA
Dimensions 2.48 (W) x 3.86 (H) x 1.12 (D) inches
63 (W) x 98 (H) x 28.5 (D) mm
Weight w/Battery 6.35 ounces ~ 180g
1201XT
Output Power 30mW
Max Modulation Sensitivity +20dBM ~ 0dBm
MIC Level / Imped. (Dynamic) -60dBm / 2.2kΩ (± 5kHz Dev.)
Phantom Power 48V ±2V @ 2mA
Power Requirements 3V DC (2 “AA” Alkaline) @ < 180mA - 290 mA w/Phantom Power ON
Dimensions 1.57 (W) x 4.49 (H) x 1.57 (D) inches
40 (W) x 114 (H) x 40 (D) mm
Weight w/Battery 6.35 ounces ~ 180g
Due to constant improvements, specications are subject to change without notice.
Licensing
Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license depends largely on the user’s classication, applica-
tion and frequency. Contact the appropriate agency (FCC in the USA) for further information.
SPECIFICATIONS
Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010
tel - 516.328.7500 • fax - 516.328.7506 • email - sales@azdencorp.com
© 2010 Azden Corporation Printed in USA P1030-02

Summary

Specifications

Using the 1201 XT Transmitters Controls and Display

Transmitter Power Control

Controls the ON/OFF state of the 1201XT transmitter.

Transmitter Audio Switch

Manages the audio signal, offering ON or ST.BY (mute) modes.

Transmitter Microphone Input

Connects microphones and supports 48VDC Phantom Power.

Transmitter Input Gain Adjustment

Adjusts the microphone input level via screwdriver.

Setting the Transmitting Frequency on the 1201 BT

Powering the 1201 XT Transmitter

Receiver Setup (1201 URX;AB and 1201 URX;VM)

Attaching Antennas

Connecting the Output Cable

Setting the Receiving Frequency

Sets the receiver frequency to match the transmitter.

Receiver Setup;Use - 1201 URX;AB or 1201 URX;VM

Receiver Power

Receiver RF Signal Display

Receiver AF (Audio Level) Display

Receiver LCD Display

Using the 1201 Transmitter Controls and Display

Transmitter Power ON;OFF

Transmitter Audio Switch (ST.BY)

Transmitter Microphone Input Connector

4-pin Hirose connector for microphone input.

Transmitter Input Level Adjustment

Adjusts microphone input gain using a screwdriver.

Powering the 1201 BT Transmitter

1201 URX;Si Top Panel Display and Operation

Mode Switch Functions

Mode #1 (GR)

Mode #2 (CH)

Mode #3 (SQ)

Mode #4 (SQ Level)

Azden 1201XT Specifications

General

Brand	Azden
Model	1201XT
Category	Microphone system
Language	English