Banner TL50 Pro Series - Mounting Bracket Options

Mounting Brackets
All measurements are listed in millimeters [inches], unless noted otherwise.
SMB30A
• Right-angle bracket with curved
slot for versatile orientation
• Clearance for M6 (¼ in)
hardware
• Mounting hole for 30 mm sensor
• 12-ga. stainless steel
45
61
69
A
B
C
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
SMB30FA
• Swivel bracket with tilt and pan
movement for precise
adjustment
• Mounting hole for 30 mm sensor
• 12-ga. 304 stainless steel
• Easy sensor mounting to extrude
rail T-slot
• Metric and inch size bolt
available
A
B
68.9
36.3
83.2
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 - 1.5 x 50
Hole size: B= ø 30.1
SMB30MM
• 12-ga. stainless steel bracket
with curved mounting slots for
versatile orientation
• Clearance for M6 (¼ in)
hardware
• Mounting hole for 30 mm sensor
70
57
A
B
C
57
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
SMBAMS30P
• Flat SMBAMS series bracket
• 30 mm hole for mounting
sensors
• Articulation slots for 90°+
rotation
• 12-ga. 300 series stainless steel
45
93
A
C
B
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
SMBAMS30RA
• Right-angle SMBAMS series
bracket
• 30 mm hole for mounting
sensors
• Articulation slots for 90°+
rotation
• 12-ga. (2.6 mm) cold-rolled steel
53
48
45
A
C
B
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
SMB30SC
• Swivel bracket with 30 mm
mounting hole for sensor
• Black reinforced thermoplastic
polyester
• Stainless steel mounting and
swivel locking hardware included
67
58
29
B
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
LMBE12RA35
• Direct mounting of stand-off pipe, with
common bracket type
• Zinc-plated steel
• 1/2-14 NPSM nut
• Mounting distance from the wall to the
center of the 1/2-14 NPSM nut is 35 mm
Hole center spacing: 20.0
38.25
57
2X Ø9
1/2 - 14
NPSM NUT
55
35
LMBE12RA45
• Direct mounting of stand-off pipe, with
common bracket type
• Zinc-plated steel
• 1/2-14 NPSM nut
• Mounting distance from the wall to the
center of the 1/2-14 NPSM nut is 45 mm
Hole center spacing: 35.0
38.25
81
65
45
2X Ø11
1/2 - 14
NPSM NUT
LMB Sealed Right-Angle Bracket
Model
Description Construction
LMB30RA
Direct-Mount Models: Bracket kit with base, 30 mm
adapter, set screw, fasteners, O-rings, and gaskets.
Black polycarbonate
LMB30RAC Gray polycarbonate
LMBE12RA
Pipe-Mount Models: Bracket kit with base, ½-14 pipe
adapter, set screw, fasteners, O-rings, and gaskets.
For use with stand-off pipe (listed and sold separately).
Black polycarbonate
LMBE12RAC Gray polycarbonate
TL50 Pro Tower Light
10 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 209142 Rev. D