Page 11;&(%$*4.8"4,7%H'*#$"&8#>%/7*,#*%4,77%IJKKKJKLLJMNON1Item 64533
FB;6PQRS6=BPTRUVBTUP6UBUW6 F6P?S
U&$*- The Inflator/Deflator has a sleep mode feature that powers off the unit after
approximately 5 minutes of nonuse. Press the Power button to turn the unit back on.
U&$"4*- The Inflator/Deflator can become hot during use. Allow the Inflator/Deflator to cool for ten minutes
after each ten minutes of continuous use. Allow Inflator/Deflator to cool 30 minutes before storing away.
T827,$"83%W,(%&(%<"4D47*%P"(*#
1. Remove the High Pressure Hose
from its storage area.
2. W,(%P"(*#- Remove tire’s valve cap.
Move Tire Inflator’s Lever straight up
and push it over tire’s valve stem. Move
the Lever to the locked position.
3. <"4D47*%P"(*#-
a. F4.(,9*(%!,7\*- Remove tire’s valve
cap. Move Tire Inflator’s Lever straight
up and push it over the tire’s valve stem.
Move the Lever to the locked position.
b. S(*#$,%!,7\*- Remove tire’s valve cap. Open
the valve tip. Thread Presta Valve Adapter
on to valve stem. Move Tire Inflator’s Lever
straight up and push it over the Presta Valve
Adapter. Move the Lever to the locked position.
U&$"4*-%%V,]*%#'(*%$.*%P"(*%T827,$&(%"#%2"(57D%
7&4]*9%"8%/7,4*%+*2&(*%$'(8"83%&8%$.*%T827,$&(1
4. Turn on the unit by pressing Power
Button (Inflating will not start yet).
5. If desired, program S(*##'(*%F.'$JR22-
a. Select pressure unit by pressing the
Power button until the desired unit is
displayed (PSI, BAR or kPa).
b. Set pressure by pressing the
SFT%f or SFT%g buttons until the
proper pressure is displayed.
U&$*- When the programmed pressure
is reached, pump will shut off.
S&)*(
SFT%f SFT%g
S(*##'(*%
?8"$
S(*##'(*
XB=UTUYi%%PR%S=6!6UP%F6=TR?F%TUh?=Q%BU[%
[6BPC%;=RV%6cSZRFTRU-%[&%8&$%&\*("827,$*1%%
[&%8&$%7*,\*%'8"$%'8,$$*89*9%)."7*%"827,$"831
6. To start inflating, press the
Pump Selection Switch to High Pressure (I).
7. To stop inflating, press the
Pump Selection Switch to Off (O).
8. When finished, move Tire Inflator’s
Lever straight up and remove.
9. Turn off the unit by pressing and
holding the Power button.
10. Unplug or remove Battery Pack after use. Clean,
then store the unit indoors out of children’s reach.
T827,$"83%F5,77%T827,$,+7*#%
1. Remove the High Pressure Hose
from its storage area.
2. Move Tire Inflator’s Lever straight up and insert
adapter. Move the Lever to the locked position.
P,/*(*9%B9,/$*(
<,77%U**97*%B9,/$*(
3. Connect adapter to the item to be inflated.
4. Turn on the unit by pressing Power
Button (Inflating will not start yet).
XB=UTUYi%%PR%S=6!6UP%F6=TR?F%TUh?=Q%
;=RV%6cSZRFTRU-%[&%8&$%&\*("827,$*1%%[&%
8&$%7*,\*%'8"$%'8,$$*89*9%)."7*%"827,$"831
U&$*-%%When inflating items to 10 PSI or less, inflate in
short bursts and check item’s pressure after each burst.
5. To start inflating, press the
Pump Selection Switch to High Pressure (I).
6. To stop inflating, press the
Pump Selection Switch to Off (O).
7. When finished, move Tire Inflator’s
Lever straight up and remove.
8. Turn off the unit by pressing and
holding the Power button.
9. Unplug or remove Battery Pack after use. Clean,
then store the unit indoors out of children’s reach.
To Next Page
Loading...
