EasyManua.ls Logo

Bauer 1632E-B - User Manual

Bauer 1632E-B
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5
%65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5
Owner’s Manual & Safety Instructions
Save This Manual%Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2016 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and s er vi ce m ay n ot be i nc lu de d.
;*,9%$."#%5,$*(",7%+*2&(*%'#"83%$."#%/(&9'4$1%
<,"7'(*%$&%9&%#&%4,8%(*#'7$%"8%#*("&'#%"8='(>1%
?@!6%ABC?%D@EF@G1
;6!%HI=

Table of Contents

Questions and Answers

  • E
    Elizabeth SnyderAug 2, 2025
    Why is my Bauer 1632E-B Power Tool overheating?
    • E
      Erin EdwardsAug 2, 2025
      Your Bauer Power Tool may be overheating because you are forcing the tool to work too fast, the chisel is dull or damaged, the motor housing vents are blocked, or the motor is being strained by a long or small diameter extension cord. To resolve this, allow the tool to work at its own rate, keep cutting chisels sharp and replace them as needed, wear ANSI-approved safety goggles and a NIOSH-approved dust mask/respirator while blowing dust out of the motor using compressed air, and eliminate the use of an extension cord (if one is needed, use one with the proper diameter for its length and load).
  • S
    smithsarahAug 8, 2025
    What to do if my Bauer 1632E-B Power Tool will not start?
    • R
      Rebecca HerreraAug 9, 2025
      If your Bauer Power Tool will not start, it could be due to several reasons. First, check that the cord is plugged in. Second, ensure that there is power at the outlet; if not, turn off the tool and check the circuit breaker, ensuring the circuit has the right capacity and no other loads. Third, if equipped, the tool’s thermal reset breaker may have tripped; turn off the tool, allow it to cool, and press the reset button on the tool. Finally, there may be internal damage or wear, in which case you should have a technician service the tool.
  • J
    Joseph CastroAug 14, 2025
    Why Bauer 1632E-B performance decreases over time?
    • V
      vgibsonAug 14, 2025
      The performance of your Bauer Power Tool may decrease over time because the chisel is dull or damaged (keep cutting chisels sharp and replace as needed), the internal lubrication is cold (allow the tool to operate with no load for 2 minutes before use), or the carbon brushes are worn or damaged (have a qualified technician replace brushes).
  • D
    daughertybradAug 20, 2025
    Why is my Bauer 1632E-B Power Tool operating slowly?
    • G
      Gabriel BirdAug 21, 2025
      Your Bauer Power Tool might be operating slowly because the extension cord is too long or the wire size is too small. Try eliminating the use of an extension cord. If an extension cord is needed, use a shorter/heavier gauge cord.
  • J
    Jordan HughesAug 27, 2025
    What causes excessive noise in a Bauer 1632E-B Power Tool?
    • J
      James SanchezAug 27, 2025
      Excessive noise or rattling in your Bauer Power Tool is caused by internal damage or wear, such as to the carbon brushes or bearings. In this case, have a technician service the tool.

Summary

General Safety Information

Work Area Safety

Electrical Safety

Guidelines for preventing electric shock hazards during operation.

Personal Safety Precautions

Measures to protect the operator's physical well-being.

Tool Use and Specific Safety

Percussion Hammer Safety Warnings

Specific safety advice for operating percussion hammers.

Vibration and Grounding Safety

Vibration Safety

Guidance to reduce risks associated with tool vibration exposure.

Grounding Requirements

Importance and methods of proper grounding for electrical tools.

Specifications and Setup

Initial Setup and Assembly

Operating Procedures

Tool Setup for Operation

Mounting Chisels

Work Area and General Operation

Work Piece and Area Setup

General Operating Instructions

Maintenance and Servicing

Cleaning and Maintenance

Carbon Brush Replacement

Troubleshooting

Common Problems and Solutions

Guide to diagnose and resolve typical issues with the tool.

Bauer 1632E-B Specifications

General IconGeneral
BrandBauer
Model1632E-B
CategoryPower Tool
LanguageEnglish

Related product manuals