Page 14 >"-&#$95<19)(&?2$+#1"<+@&,($)+$&9)((&ABCCCBCDDBEFGF/ Item 57151
HI>;JK LM;NIJOL! PIO!J;!I!Q;H;JRM
S"-X,1$9$&H$#&R,
1. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
2. Cut only the following materials:
Dimensional lumber, plywood, particle board, plastic.
!"#$% Use caution to avoid overheating the cutting tips.
If cutting plastic, cut at an even pace to avoid melting it.
3. Refer to cutting capacities in the Specifications Table
on page 8 for limitations on workpiece size.
4. Allow room on both left and right sides
of Saw for extended workpieces.
5. Use additional supports if needed to ensure
the stability of the workpiece. Mount the Saw
so that the surface is level to the ground, and
additional supports to provide a surface on the
same level as the saw table. If the work surface
and any workpiece supports are not level, and
on the same level, unwanted bevel angles will
appear in the cuts resulting in poor joinery.
6. Secure workpieces to the saw table using the Clamp
or other clamping devices (not included). Securing
the workpiece will provide safety by preventing kick
back and by removing the need to hold workpieces
near the blade by hand. Clamping the workpiece
will also improve cutting accuracy by preventing the
workpiece from moving during the cutting operation.
R+1<8$&S"-X,1$9$&;Z#$<+1"<&H2,,"-#+
1. The Table Extensions are located on each
side of the Table, and locked in place using
the Table Extension Lock Levers.
2. When properly installed, the upper face of
the Table Extensions are level with the Table,
and provide a wider support surface for the
workpiece. Each Extension has a Cut Stop Lever
which can be raised to make repetitive cuts.
3. Support the workpiece to be level with the table,
and so that after the cut is made the cut off pieces
will not fall. Use sawhorses or other supports
(not included) to support longer workpieces.
4. If the workpiece is not level, you will make
an unintentional bevel cut in the material.
If the workpiece is not supported, it will bind
the blade and may cause the material to
kick back, potentially causing injury.
T$<$-)(&O<+#-29#1"<+&7"-&R+$
1. Make sure that the Trigger is in the
off-position, then plug in the tool.
SIN!O!Ti&&JL&MN;0;!J&H;NOLRH&O!jRNK%
The tool will restart automatically if stalled.
H(1*1<8&P1#$-&H)3&Q2##1<8&M-"9$*2-$
2. Unlock the Head Lock-Down Pin.
3. Check that all adjustment knobs are tight (Miter
Lock Handle, Bevel Lock Handle, Fence Lock
Knobs, and Table Extension Lock Levers).
4. Blow any sawdust or debris away from the Fence.
Place the work material against the Fence.
5. To use the Shadow Cut Line Guide System to
align the cut, turn its Switch on. Pull the Saw
Head down until the Saw Blade is close to the
workpiece and the Blade’s shadow appears on
the work material, indicating where the Blade will
cut. Align the marked location of the cut on the
workpiece with the edge of the Saw Blade shadow.
6. The Saw will also operate without using the
Shadow Cut Line Guide System if desired. In that
case align the marked location of the cut on the
work material with the saw blade. To prevent the
workpiece from being cut too short, align the edge
of the blade with the measured mark, keeping the
rest of the blade on the waste side of the cut.
7. Hold the work material in place using the Clamp.
Ensure that the work material is level and supported
securely. Use saw horses or supports if necessary.
VI!T;Ni&H)3+&9)<&?219X(.&
):,2#)#$&71<8$-+&17&:1+2+$*/&&&
Y$$,&5)<*+&3$((&9($)-&"7&92##1<8&)-$)/
8. Grip the Saw Handle, press the Trigger
Lock Button with your thumb, and
squeeze the Trigger to start the Saw.
9. Use two hands and hold workpiece securely
against table and fence at all times.
To Next Page
Loading...
