Bauknecht BFP 5O41 PLT X

Questions and Answers

R
Robert RussellAug 18, 2025
Why my Bauknecht BFP 5O41 PLT X is not working / will not start?
- L
  Lawrence CampbellAug 18, 2025
  If the Bauknecht Dishwasher is not working or won't start, consider these potential causes: * The appliance must be switched on. Check the household circuit fuse if there is no power supply. * The appliance door doesn’t close. Check if the appliance door is closed. * “Start Delay” option is ON. Check whether the „Start Delay” option has been selected. If it has, the appliance will start once the set time has elapsed. If necessary, Reset the current cycle by switching OFF the dishwasher, then switch it on again, select a new cycle, press START/PAUSE and close the door.
J
Jacob JensenAug 20, 2025
What does F6 symbol mean on Bauknecht BFP 5O41 PLT X and how to fix it?
- U
  uhermanAug 20, 2025
  If the Bauknecht Dishwasher displays 'F6', it could be due to: * Low water pressure: Ensure the water tap is fully open during water inlet (minimum capacity: 0.5 liters per minute). * Kinked water inlet hose or clogged inlet filters: Ensure the water inlet hose is not kinked and the inlet filter in the water tap connector is not dirty or clogged.
S
Shelia Zamora MDAug 23, 2025
How to fix CHECK SALT! or ADD SALT error on Bauknecht BFP 5O41 PLT X Dishwasher?
- A
  Amber GarrettAug 23, 2025
  If the Bauknecht Dishwasher displays 'CHECK SALT!' or 'ADD SALT', it means the salt reservoir is empty. Refill it with salt and adjust the water hardness accordingly.
M
Mr. Shawn ScottAug 26, 2025
What to do if Bauknecht Dishwasher shows CHECK RINSE AID! or ADD RINSE AID?
- E
  Elizabeth ParkAug 26, 2025
  If the Bauknecht Dishwasher displays 'CHECK RINSE AID!' or 'ADD RINSE AID', it indicates that the rinse aid dispenser is empty. Simply refill the dispenser with rinse aid.
J
Jeffrey PerryAug 27, 2025
What to do if my Bauknecht BFP 5O41 PLT X displays PRESS START AND CLOSE THE DOOR?
- X
  xfieldsAug 27, 2025
  If the Bauknecht Dishwasher displays 'PRESS START AND CLOSE THE DOOR', it means the door was not closed within 4 seconds of pressing the start button. Press the start button again and ensure the door is closed within 4 seconds.
C
christinaandersenAug 30, 2025
What to do if Bauknecht BFP 5O41 PLT X displays F2 error?
- T
  Tonya McneilAug 30, 2025
  If the Bauknecht Dishwasher displays 'F2', it could be due to several reasons: * Dirty filters or spray arms: Clean the filters and spray arms. * Too little water: Ensure concave items are arranged facing downwards in the rack. * Incorrectly fitted drain hose: Make sure the drain hose is fitted correctly. * High level of foam: Repeat the cycle without detergent or wait until the foam disappears. * Low water pressure: Ensure the water tap is fully open during water inlet (minimum capacity: 0.5 liters per minute). * Kinked water inlet hose or clogged inlet filters: Ensure the water inlet hose is not kinked and the inlet filter is clean.
L
Luke HudsonSep 1, 2025
Why do dishes and glass have calcination whitish film in my Bauknecht Dishwasher?
- B
  Bobby HughesSep 1, 2025
  If dishes and glass have a calcination whitish film, this could be due to: * Low salt level: Fill the salt reservoir. * Inadequate water hardness adjustment: Increase the values. * Improperly closed salt reservoir cap: Check that the salt reservoir cap is properly closed. * Insufficient rinse aid: Add rinse aid or adjust the dosage levels higher.
L
lance63Sep 3, 2025
How to troubleshoot F3 error on Bauknecht Dishwasher?
- T
  Thomas VazquezSep 3, 2025
  If your Bauknecht Dishwasher displays 'F3', it could be due to dirty filters, a kinked drain hose, or a closed syphon hose connection. Clean the filters, ensure the drain hose is not kinked, and remove the closure disk of the syphon hose connection.
P
Pamela VelasquezSep 6, 2025
What to do if Bauknecht BFP 5O41 PLT X displays OPEN AND CLOSE THE DOOR?
- L
  linda52Sep 6, 2025
  If the Bauknecht Dishwasher displays 'OPEN AND CLOSE THE DOOR', it indicates that the door was not opened between cycles. Unload the appliance (if not already), and then open and close the door.
K
Kristen ContrerasSep 8, 2025
How to fix Bauknecht BFP 5O41 PLT X door if it doesn't close?
- T
  Tanya JohnsonSep 8, 2025
  If the Bauknecht Dishwasher door doesn’t close properly, make sure that the racks are fit to the end and vigorously push the door until you hear the “clack” sound.

Bauknecht BFP 5O41 PLT X Specifications

General

Type	Freestanding
Noise Level	41 dB
Dimensions (HxWxD)	85x60x60 cm
Water Consumption per Cycle	9.5 L
Number of Programs	10
Display	Yes
Control panel colour	Stainless steel
Noise emission class	B
Delayed start timer	Yes
Delay start (max)	24 h
AquaStop function	Yes
Power consumption (off)	0.5 W
Connected load	1900 W
Current	10 A
Width	60 cm
Depth	60 cm
Height	85 cm
Weight	47 kg
Drying Efficiency Class	A
Half Load Option	Yes
Number of Place Settings	14 place settings
Product size	Full-size
Inlet hose length	155 cm
Outlet hose length	1.5 m
Washing programs	Eco
Cycle time	240 min
Annual Energy Consumption	65 kWh
Energy consumption per cycle	0.83 kWh