Baxi DUO-TEC COMPACT+ - PARAMETERS SETTING; Adjusting Maximum Heating Power

7651556.01 (1-01/16) 36
INSTALLER Section (en)
14. PARAMETERS SETTING
7RSURJUDPPHWKHSDUDPHWHUVRIWKHERLOHUHOHFWURQLFERDUGSURFHHGDVIROORZV
• Press and WRJHWKHUDQGKROGWKHPGRZQIRUVHFRQGVXQWLOSURJUDPPHURZ³P01” appears on the display alternated
ZLWKWKHVHWYDOXH
• Press
WRVFUROOWKHOLVWRISDUDPHWHUV
• Press
WKHYDOXHRIWKHVHOHFWHGEHJLQVÀDVKLQJSUHVV WRFKDQJHWKHYDOXH
• Press
WRFRQ¿UPWKHYDOXHRUSUHVV WRH[LWZLWKRXWVDYLQJ
)XUWKHU LQIRUPDWLRQ FRQFHUQLQJ WKH SDUDPHWHUV OLVWHG LQ WKH IROORZLQJWDEOHDUHVXSSOLHGWRJHWKHUZLWKWKHUHTXLUHG
accessories.
DESCRIPTION OF PARAMETERS
FACTORY SETTINGS
1.24 20 24 28
P01 Manufacturer information 00
P02
Gas used
00 0(7+$1(01 /3*
00
P03
Hydraulic system
00 LQVWDQWDQHRXVDSSOLDQFH
05 DSSOLDQFHZLWKH[WHUQDOVWRUDJHERLOHU
08 KHDWLQJRQO\DSSOLDQFH
08 00 00 00
P04
Programmable relay 1 settings (See SERVICE instructions)
00 QRDVVRFLDWHGIXQFWLRQ
01 UHOD\FRQWDFWFORVHGZLWK5RRP7KHUPRVWDWGHPDQG9
02 UHOD\FRQWDFWFORVHGZLWK5HPRWH&RQWUROGHPDQGORZYROWDJH
03 V\VWHP¿OOFRQWDFW
04 ERLOHUIDXOW\VLJQDOFRQWDFW
05 IDQFRQWDFWNLWFKHQIDQ
06-07 QRWXVHG
08 WLPHGFRQWDFWIRUHQDEOLQJH[WHUQDO'+:SXPS
09 WLPHGFRQWDFWIRUHQDEOLQJH[WHUQDO'+:FLUFXODWLRQSXPSYLD'+:SURJUDPPLQJ
from remote control
10 UHOD\FRQWDFWFORVHGZLWK':+GHPDQGDFWLYH
11 - 12 - 13 QRWXVHG
02
P05
Programmable relay 2 settings (See SERVICE instructions)
6DPHFRQ¿JXUDWLRQVDVUHOD\3
04
P06
([WHUQDOSUREHLQSXWFRQ¿JXUDWLRQ
(See SERVICE Instructions)
00
P07..P09 Manufacturer information --
P10
Heating setpoint setting OT / RT
(Remote Control - Open Therm / Room Thermostat 230V~)
00 WKHWHPSHUDWXUHUHTXHVWLVWKH5HPRWH&RQWUROVHWSRLQW
01 WKH WHPSHUDWXUH 5HTXHVW LV WKH KLJKHVW VHWSRLQW EHWZHHQ 5HPRWH &RQWURO DQG
PCB
02 WKH WHPSHUDWXUH UHTXHVW LV WKH 5HPRWH &RQWURO VHWSRLQW7KH 5RRP 7KHUPRVWDW
enable the gas boiler operates
03  WKH FDOFXODWHG VHWSRLQW GHSHQGV RQ WKH RULJLQ RI WKH UHTXHVW 3&% RU 5HPRWH
Control):
D3&%$PELHQW7KHUPRVWDW the setpoint is set by pressing the +/-
buttons
RQWKHERLOHUFRQWUROSDQHODIWHUKDYLQJ¿UVWGLVFRQQHFWHGWKH5HPRWH&RQWUROIURP
the boiler.
E5HPRWH&RQWUROthe setpoint is set by modifying the “ULt” parameter (see Room
Unit accessory manual, chapter “INSTALLER FUNCTIONS”)
F6LPXOWDQHRXVUHTXHVW3&%  5HPRWH &RQWURO WKHKLJKHUVHWSRLQW RI WKH WZR
UHTXHVWVLVVDWLV¿HG
00
P11..P12 Manufacturer information --
P13 Max. heating output (0-100%) 100 80 80 86
P14 DHW max. output (0-100%) 100 80 100 100
P15 Min. heating output (0-100%) 00
P16
0D[LPXP&+VHWSRLQW&
00 &01 &
00
P17 Pump overrun time in heating mode (01-240 minutes) 03