Need help?Do you have a question about the Behringer Xenyx XL3200 and is the answer not in the manual?
General| Type | Analog |
|---|---|
| Channels | 32 |
| Line Inputs | 32 |
| Aux Sends | 4 |
| Phantom Power | Yes |
| Effects | No |
| USB Interface | No |
| Main Outputs | 2 |
| Other Outputs | 2 |
| EQ Bands | 3 |
Details exclusions for consumables, modifications, hardware/software, serial numbers, and improper handling.
Explains warranty is only for the original buyer and cannot be transferred.
Limits liability for consequential/indirect loss and liability to product value.
States this warranty is the complete warranty and supersedes all other communications.
Addresses statutory consumer rights and mandatory local laws.
Notes that warranty service conditions are subject to change without notice.
Instructions for checking packaging, handling damaged units, and using protective cases.
Guidance on air supply, fuse replacement, power connection, and grounding.
Encourages registering the product for faster warranty service.
Explains the manual's structure and where to find more information.
Illustrates connecting microphones, instruments, and external processors.
Diagrams connections for P.A. systems, stage monitors, and recording devices.
Details on unbalanced TS, balanced TRS, XLR, and RCA connector types and wiring.
Information on IEC receptacle, fuse holder, power switch, and serial number.
Description of XLR (MIC) and 1/4" (LINE) inputs, including phantom power.
Details various connector types: Insert, Direct Out, Stereo Inputs, Main Mix Outputs, Subgroups, and CD/Tape.
Explains controls for mono channels: +48V, Trim, 80 Hz filter, EQ, High, High Mid, Low Mid, Low.
Details the LOW MID EQ and LOW EQ controls and the EQ push-button.
Describes routing signals to effects, monitors, and auxiliary buses.
Explains channel fader adjustment, pan control, mute switch, and solo function.
Covers CLIP/SIG LEDs, fader adjustment, and routing signals to subgroups/main mix.
Details controls for stereo channels: +48V, Mic Trim, 80 Hz, Line Trim.
Describes the 4-band EQ for stereo channels and their aux/FX send paths.
Covers stereo channel fader, balance control, mute, and solo functions.
Explains solo function, CLIP/SIG LEDs, fader adjustment, and routing signals.
Covers MAIN MUTE, MAIN A fader, MAIN B level, and BAL(ANCE) control.
Describes the LED meters for monitor and main output levels, including solo mode.
Explains subgroup faders, pan control, MAIN switch, SOLO, and CLIP for routing and monitoring.
Covers talkback microphone, level control, and routing options.
Details talkback mic, solo level, PFL/AFL switches for monitoring.
Covers CD/TAPE input level/main switch and headphone/speaker volume controls.
Explains MAIN B routing, STEREO/MONO, PRE/POST, and FX SEND controls.
Details MON send faders, MUTE, and SOLO switches for monitor mix adjustments.
Covers AUX send/return controls, PRE/POST selection, and MUTE/SOLO functions.
Instructions for modifying monitor/aux sends to be post-EQ.
Instructions for modifying direct outputs to be pre-fader.
Details microphone and line input specs: EIN, frequency response, impedance, gain, and level.
Specs for channel inserts, direct outs, crosstalk, and frequency response.
Specs for stereo inputs, subgroup outputs, group inserts, main outputs, inserts, speakers, phones, CD/Tape.
Specs for EQ bands on mono and stereo channels: frequency ranges and boost/cut levels.
Specs for crosstalk, frequency response, and noise levels for the main mix system.
Details power consumption, fuse rating, and mains connector type.
Lists dimensions (H x W x D) and net weight for each model.
To Next Page
