What to do if the Rinse Symbol is flashing on my Beko WMI 71641?
If the Rinse Symbol is flashing on your Beko Washer (or the water cut-off symbol is lit), it indicates that the water supply may have been cut off. After ensuring the water is back on, restart the machine by pressing the «Start/ Pause/Cancel» button briefly.
What to do if my Beko WMI 71641 does not discharge water?
If your Beko Washer isn't discharging water, the water outlet hose might be clogged or twisted, or the pump filter could be clogged. Try cleaning or flattening the hose and cleaning the pump filter to resolve this issue.
What to do if my Beko WMI 71641 it did not spin?
If your Beko Washer didn't spin, it might be due to an imbalance of laundry, causing the program to complete without spinning. Also, the machine won't spin if the water hasn't completely drained. Rearrange and re-spin the laundry if it's clustered. Check the filter and drain hose for blockages.
What to do if my Beko Washer programme cannot be started or selected?
If your Beko Washer programme can't be started, the machine may have entered self-protection mode due to an infrastructure issue like line voltage or water pressure. To reset, bring your machine to factory settings by turning the Programme selection knob.
What to do if there is water coming from the bottom of my Beko WMI 71641 Washer?
If water is leaking from the bottom of your Beko Washer, there may be issues with the hoses or the pump filter. Ensure the water inlet hose seals are secure, the drain hose is tightly attached to the tap, and the pump filter is completely closed.
What to do if my Beko Washer continuously spins and the remaining time doesn't count down?
If your Beko Washer spins continuously without the timer counting down, the laundry may be imbalanced. The automatic spin correction system might be activated due to uneven distribution. Try rearranging and re-spinning the laundry, especially if it's clustered. The machine prevents spinning if the load isn't evenly distributed to avoid damage.
Why my Beko WMI 71641 colour of the clothes faded?
Clothes fading in your Beko Washer can occur if the machine is overloaded, the detergent is damp, or a higher temperature was selected. To prevent this, avoid overloading the machine, store detergent in a closed, dry place away from high temperatures, and select the appropriate program and temperature for the laundry type and soil level.
What to do if my Beko WMI 71641 washing performance is poor and laundry turns grey?
If your Beko Washer results in grey laundry, it may be due to using too little detergent over a long time, washing at low temperatures for extended periods, using insufficient detergent for hard water, or using too much detergent. Use the recommended amount of detergent for your water hardness and laundry load, and select the right temperature. Note that greyness is difficult to remove once it sets in.
Why is there detergent left on the laundry after washing in my Beko WMI 71641?
Detergent residue on laundry after washing in your Beko Washer can be due to overloading the machine, selecting the wrong program or temperature, or using the wrong detergent. Avoid overloading, select the correct program and temperature, and use appropriate detergents like wool detergents for woollens.
What to do if my Beko WMI 71641 loading door won't open?
If the loading door of your Beko washer won't open, it could be due to a few reasons: * The door lock might be activated because of the water level; drain the water by running the Pump or Spin programme. * The machine might be heating water or in the spinning cycle; wait until the programme completes. * The child lock might be engaged; wait a couple of minutes for deactivation.
General| Load Capacity | 7 kg |
|---|---|
| Spin Speed | 1600 rpm |
| Energy Efficiency Class | A+++ |
| Noise Level (Washing) | 53 dB |
| Water Consumption (annual) | 9020 liters |
| Dimensions (Third AI) | 85 x 60 x 53 cm |
To Next Page
