EasyManua.ls Logo

Beko WMI 71641 - User Manual

Beko WMI 71641
56 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
2820521336/ 02-12-15.(16:05)
Document Number=
Washing Machine
User Manual
WMI 71641
WMI 71441
EN

Table of Contents

Other manuals for Beko WMI 71641

Questions and Answers

  • B
    Brent Johnson IIISep 12, 2025
    Why does my Beko WMI 71641 programme time not countdown?
    • K
      Kevin BurnsSep 12, 2025
      If the programme time on your Beko washer isn't counting down, the timer may stop during water intake until the machine takes in enough water. It might also stop during the heating step until the machine reaches the selected temperature, or during the spinning step, if the laundry is unbalanced.
  • T
    Taylor GreenAug 25, 2025
    What to do if my Beko WMI 71641 does not discharge water?
    • T
      Tamara HatfieldAug 25, 2025
      If your Beko Washer isn't discharging water, the water outlet hose might be clogged or twisted, or the pump filter could be clogged. Try cleaning or flattening the hose and cleaning the pump filter to resolve this issue.
  • S
    Savannah JacksonAug 25, 2025
    What to do if my Beko WMI 71641 it did not spin?
    • L
      laurenschmidtAug 26, 2025
      If your Beko Washer didn't spin, it might be due to an imbalance of laundry, causing the program to complete without spinning. Also, the machine won't spin if the water hasn't completely drained. Rearrange and re-spin the laundry if it's clustered. Check the filter and drain hose for blockages.
  • B
    Beverly MartinSep 23, 2025
    Why is my laundry still wet after the programme ends on my Beko WMI 71641 Washer?
    • S
      Sheila HamiltonSep 23, 2025
      If your laundry is still wet after the programme ends on your Beko washer, it's possible that excessive foam occurred, activating the automatic foam absorption system due to too much detergent usage. Use the recommended amount of detergent.
  • K
    Krystal ReedSep 13, 2025
    Why did my Beko WMI 71641 Washer stop shortly after starting a programme?
    • J
      Jennifer HendricksSep 13, 2025
      If your Beko washer stopped temporarily shortly after the programme started, it might be due to low voltage. The machine will resume running when the voltage returns to normal.
  • J
    Joseph JohnsonSep 18, 2025
    Why is there detergent residue in the detergent drawer of my Beko Washer?
    • C
      Cheryl JohnsonSep 18, 2025
      If you find detergent residue in the drawer of your Beko washer, it could be due to several reasons: * Putting detergent in a wet drawer; dry the drawer first. * The detergent has gotten damp; keep detergents dry. * Low water pressure; check the water pressure. * Blocked detergent compartment holes; check and clean them. * Detergent might be mixed with the softener; do not mix the softener with detergent.
  • K
    Kyle EvansSep 6, 2025
    Why my Beko WMI 71641 colour of the clothes faded?
    • A
      Alyssa VegaSep 6, 2025
      Clothes fading in your Beko Washer can occur if the machine is overloaded, the detergent is damp, or a higher temperature was selected. To prevent this, avoid overloading the machine, store detergent in a closed, dry place away from high temperatures, and select the appropriate program and temperature for the laundry type and soil level.
  • F
    Fernando ByrdSep 6, 2025
    What to do if my Beko WMI 71641 washing performance is poor and laundry turns grey?
    • R
      Rachael AndersonSep 6, 2025
      If your Beko Washer results in grey laundry, it may be due to using too little detergent over a long time, washing at low temperatures for extended periods, using insufficient detergent for hard water, or using too much detergent. Use the recommended amount of detergent for your water hardness and laundry load, and select the right temperature. Note that greyness is difficult to remove once it sets in.
  • M
    mbrownSep 23, 2025
    Why is there detergent left on my laundry after washing in my Beko WMI 71641 Washer?
    • E
      erikphelpsSep 23, 2025
      If there's detergent left on your laundry after washing in your Beko washer, it could be because: * The machine was overloaded. * The wrong programme and temperature were selected. * The wrong detergent was used. Avoid overloading, select the correct settings, and use the appropriate detergent. Clean the drum regularly.
  • M
    Michael WilliamsAug 30, 2025
    What to do if my Beko WMI 71641 loading door won't open?
    • C
      cliuAug 31, 2025
      If the loading door of your Beko washer won't open, it could be due to a few reasons: * The door lock might be activated because of the water level; drain the water by running the Pump or Spin programme. * The machine might be heating water or in the spinning cycle; wait until the programme completes. * The child lock might be engaged; wait a couple of minutes for deactivation.

Summary

General Safety Instructions

Life, Property, and Childrens Safety

Essential safety rules for product placement, usage, and protecting children.

Electrical Safety and Hot Surfaces

Guidelines for safe electrical connections and warnings about hot parts.

Installation Guide

Water Supply and Drain Connections

Instructions for correctly connecting water inlet and drain hoses.

Electrical Connection and Leveling

Procedures for safe electrical hook-up and adjusting feet for stability.

Preparing for Washing

Load Capacity, Loading, and Detergent Use

Guidance on load size, placement, and using detergents/softeners.

Operating Your Washing Machine

Control Panel and Display Symbols

Explains the functions of buttons, displays, and icons.

Programme Selection and Types

Guide to choosing wash programs, including main and special cycles.

Troubleshooting Common Issues

Service and Guarantee Information

Beko WMI 71641 Specifications

General IconGeneral
Load Capacity7 kg
Spin Speed1600 rpm
Energy Efficiency ClassA+++
Noise Level (Washing)53 dB
Water Consumption (annual)9020 liters
Dimensions (Third AI)85 x 60 x 53 cm

Related product manuals