Why is my Beko WMI 71641 directly discharging the water it takes in?
If your Beko washer is immediately discharging the water it takes in, the draining hose might not be at the correct height. Connect the water draining hose as described in the operation manual.
How to fix a Beko WMI 71641 Washer that won't start or select a programme?
If your Beko washer won't start or select a programme, it may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). To reset the machine to factory settings, press and hold the Start / Pause / Cancel button for 3 seconds.
How to fix a Beko WMI 71641 that does not fill with water?
If your Beko Washer isn't filling with water, start by checking if the tap is fully open and that the water inlet hose isn't bent. Also, the water inlet filter might be clogged, so try cleaning it. Finally, ensure that the loading door is completely closed. Open the taps fully, flatten the hose, clean the filter and close the door.
Why does my Beko Washer not switch to the spinning step?
Your Beko washer may not switch to the spinning step if there is an imbalance of laundry in the machine. The automatic unbalanced load detection system might be activated due to the laundry's distribution in the drum. Also, the machine won't spin if water is not drained completely, so check the filter and the draining hose. Excessive foam might also prevent spinning, so use the recommended amount of detergent.
What to do if my Beko WMI 71641 loading door won't open?
If the loading door of your Beko washer won't open, it could be due to a few reasons: * The door lock might be activated because of the water level; drain the water by running the Pump or Spin programme. * The machine might be heating water or in the spinning cycle; wait until the programme completes. * The child lock might be engaged; wait a couple of minutes for deactivation.
Why is my Beko WMI 71641 not filling with water?
If your Beko washer isn't filling with water, check the following: * Ensure the water tap is fully open. * Make sure the water inlet hose isn't bent; flatten it if it is. * Clean the water inlet filter if it's clogged. * Ensure the loading door is completely closed.
What to do if my Beko WMI 71641 Washer is leaking water from the bottom?
If you notice water leaking from the bottom of your Beko washer, it's likely due to issues with the hoses or the pump filter. Make sure the seals of the water inlet hoses are securely fitted. Also, ensure that the pump filter is completely closed.
What to do if my Beko Washer does not work and nothing is displayed on the screen?
If your Beko Washer isn't working and the screen is blank, check if the plug is properly inserted into the outlet, ensure the fuse hasn't blown, verify that there's no power outage, and confirm that the “On/Off” button has been pressed.
Why does my Beko WMI 71641 Washer it does not rinse well?
Poor rinsing in your Beko Washer can be caused by using an inappropriate amount, brand, or poorly stored detergent, putting detergent in the wrong compartment, a clogged machine filter, a folded drain hose, or skipped intermediate spins. Store detergent properly, ensure it's in the correct compartment, check the filter and drain hose, and rearrange laundry if there's an imbalance.
What to do if there is water coming from the bottom of my Beko WMI 71641 Washer?
If water is leaking from the bottom of your Beko Washer, there may be issues with the hoses or the pump filter. Ensure the water inlet hose seals are secure, the drain hose is tightly attached to the tap, and the pump filter is completely closed.
General| Load Capacity | 7 kg |
|---|---|
| Spin Speed | 1600 rpm |
| Energy Efficiency Class | A+++ |
| Noise Level (Washing) | 53 dB |
| Water Consumption (annual) | 9020 liters |
| Dimensions (Third AI) | 85 x 60 x 53 cm |
Essential safety rules for product placement, usage, and protecting children.
Guidelines for safe electrical connections and warnings about hot parts.
Instructions for correctly connecting water inlet and drain hoses.
Procedures for safe electrical hook-up and adjusting feet for stability.
Guidance on load size, placement, and using detergents/softeners.
Explains the functions of buttons, displays, and icons.
Guide to choosing wash programs, including main and special cycles.
To Next Page
