Why is my laundry turning gray after washing in my Beko Washer?
Laundry may turn gray after washing in your Beko Washer due to: * Using an insufficient amount of detergent over a long period. * Washing at low temperatures for a long time. * Using an insufficient amount of detergent with hard water. * Using too much detergent. Ensure you use the recommended amount appropriate for water hardness and the laundry.
Why doesn't my Beko WTV9633XC0 Washer fill with water?
There are several reasons why your Beko Washer might not be filling with water: * The tap may be turned off. Turn on the taps. * The water inlet hose may be bent. Flatten the hose. * The water inlet filter may be clogged. Clean the filter. * The loading door may be open. Close the door.
How to open the loading door of my Beko WTV9633XC0 Washer?
The loading door of your Beko Washer might not open due to a few reasons: * The door lock is activated because of the water level in the machine. Drain the water by running the Pump or Spin programme. * The machine is heating up the water or it is at the spinning cycle. Wait until the programme completes. * The child lock is engaged. The door lock will be deactivated a couple of minutes after the programme has come to an end. Wait for a couple of minutes for deactivation of the door lock.
Why is my Beko WTV9633XC0 leaking water from the bottom?
If you notice water leaking from the bottom of your Beko washing machine, it could be due to a clogged or twisted water drain hose. Clean or flatten the hose to fix this. Another possible cause is a clogged pump filter, which would also need cleaning.
Why won't my Beko WTV9633XC0 Washer go to the spinning step?
Your Beko Washer might not switch to the spinning step because: * There might be an unbalanced load in the machine. The automatic unbalanced load detection system might be activated. * The machine will not spin if water is not drained completely. Check the filter and the draining hose. * Excessive foam might have occurred. Use the recommended amount of detergent.
Why doesn't my Beko WTV9633XC0 rinse clothes well?
If your Beko Washer isn't rinsing well, it could be due to: * Inappropriate detergent amount, brand, or storage. Use a detergent appropriate for washing machines and laundry; keep detergents closed in a humidity-free environment and avoid excessive temperatures. * Detergent in the wrong compartment. Put the detergent in the correct compartment. * A clogged pump filter. Check the filter. * A folded drain hose. Check the drain hose.
Why do my clothes smell bad after washing in my Beko WTV9633XC0 Washer?
Unpleasant smells on clothes after washing in your Beko Washer can be caused by: * Odours and bacteria layers formed on the drum from continuous washing at lower temperatures and/or in short programmes. Leave the detergent drawer and the loading door ajar after each washing. * Excessive laundry loaded in the machine. Do not overload the machine. * Damp detergent. Keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures.
Why do stains persist after washing in my Beko Washer?
If stains persist or laundry isn't whitened after washing in your Beko Washer, it could be because: * You're using an insufficient amount of detergent. * The machine is overloaded. * The wrong programme and temperature were selected. * The wrong type of detergent is used. * Too much detergent is used. Ensure you use the recommended amount and type for your laundry.
Why does the programme time not countdown on my Beko Washer?
The timer on your Beko Washer may not countdown if: * The timer may stop during water intake until the machine takes in an adequate amount of water. * The timer may stop during the heating step until the machine reaches the selected temperature. * The timer may stop during the spinning step if the automatic unbalanced load detection system is activated.
Why is my Beko Washer vibrating and making noise?
Your Beko Washer might be vibrating or making noise due to several reasons: * The machine might be standing unbalanced. Adjust the feet to level the machine. * A hard substance might have entered into the pump filter. Clean the pump filter. * Transportation safety bolts are not removed. Remove the transportation safety bolts. * Laundry quantity in the machine might be too little. Add more laundry to the machine. * The machine might be overloaded with laundry. Take out some of the laundry or distribute the load by hand to balance it. * The machine might be leaning on a rigid item. Ensure that the machine is not leaning on anything.
General| Model | WTV9633XC0 |
|---|---|
| Load Capacity | 9 kg |
| Energy Efficiency Class | A+++ |
| Noise Level Spinning | 76 dB |
| Programs | 15 |
| Weight | 70 kg |
| Color | White |
| Spin Speed | 1600 rpm |
| Type | Front Load |
To Next Page
