3522.5-0000010 РЭ
222
The program No2 ensures automatic implementation of the following operations:
o marker folding;
o seeder uplift from the working position.
To record the program No2 proceed as follows:
- turn on the OPU of the HLL (if it is off), pressing the button 1 (figure 4.2.3);
ATTENTION: BEFORE STARTING TO RECORD THE PROGRAM NO2 IT IS RE-
QUIRED TO SET THE SEEDER TO A CERTAIN CONDITION IN A MANUAL MODE (THE
FAN DRIVE HYDRAULIC MOTOR TURNED ON, THE MARKERS UNFOLDED, THE
SEEDER LOWERED TO A WORKING POSITION).
- push the button 3 (figure 4.2.3) and keep it pushed until an acoustic signal goes off
(approximately two seconds) and the annunciator 6 starts blinking;
- push the buttons 13, 14 to select the sections No3 and No2 of the hydraulic distributor
EHS respectively. The annunciators of uplift and lowering 10 of these sections will start blinking;
- operating over the section No2 with the joystick 1 (figure 4.2.2) raise the marker;
- operating over the section No3 with the joystick 2 (figure 4.2.2) raise the seeder;
- repeatedly push the buttons 13, 14 (figure 4.2.3) to select the sections No3 and No2
of the hydraulic distributor EHS (the record in respect of the sections is finished);
- to complete the programming push the button 3 of the recorded program No2.
The program No3 ensures automatic implementation of the following operations:
- seeder lowering and setting a floating position;
o marker unfolding.
To record the program No3 proceed as follows:
- turn on the OPU of the HLL (if it is off), pressing the button 1 (figure 4.2.3);
ATTENTION: BEFORE STARTING TO RECORD THE PROGRAM NO3 IT IS RE-
QUIRED TO SET THE SEEDER TO A CERTAIN CONDITION IN A MANUAL MODE (THE
FAN DRIVE HYDRAULIC MOTOR TURNED ON, THE MARKERS FOLDED, THE SEEDER
IN RAISED POSITION).
- push the button 2 and keep it pushed until an acoustic signal goes off (approximately
two seconds) and the annunciator 7 starts blinking;
- push the buttons 13, 14 to select the sections No3 and No2 of the hydraulic distributor
EHS respectively. The annunciators of uplift and lowering 10 of these sections will start blinking;
- operating over the section No3 with the joystick 2 (figure 4.2.2) set a “floating” posi-
tion, herewith the indicator 9 (figure 4.2.3) will display “FL”;
- operating over the section No2 with the joystick 1 (figure 4.2.2) unfold the marker;
- repeatedly push the buttons 13, 14 (figure 4.2.3) to select the sections No3 and No2
of the hydraulic distributor EHS (the record in respect of the sections is finished);
- to complete the programming push the button 2.
ATTENTION:
BEFORE THE PROGRAM NO2 IS CARRIED OUT MAKE SURE THE SEEDER IS IN A
CORRESPONDING CONDITION – THE FAN DRIVING HYDRAULIC MOTOR HAS BEEN
TURNED ON, THE MARKERS HAVE BEEN UNFOLDED, THE SEEDER HAS BEEN LOW-
ERED TO A WORKING POSITION!
BEFORE THE PROGRAM NO3 IS CARRIED OUT MAKE SURE THE SEEDER IS IN A
CORRESPONDING CONDITION – THE FAN DRIVING HYDRAULIC MOTOR HAS BEEN
TURNED ON, THE MARKERS HAVE BEEN FOLDED, THE SEEDER IS IN A RAISED POSI-
TION!
To carry out the implementation of the recorded programs No1, No3 and No2 during the
tractor operation proceed as follows:
Entering the first run, first it is required to actuate the fan drive (shortly push the button 4
(figure 4.2.3) for implementation of the program No1. At the beginning of the run (from the
seeder hauling position) it is required to push the button 2 for the program No3 implementation,
the seeder lowering and the marker unfolding.
Leaving the run it is required to convert the seeder from its working position to the hauling
one (fold the marker, raise the seeder). To do this push the button 3 shortly to carry out the im-
plementation of the program No2.
The fan driving hydraulic motor is disabled at the end of the field operation by repeated
pushing the button 4 shortly.
https://tractormanualz.com/
To Next Page
