EasyManua.ls Logo

bemodern 1198 - User Manual

bemodern 1198
6 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
200663_03 Page 1
User Instructions for Remote Controlled
2kW Rotisserie Effect Fan Heater
These instructions should be read carefully and retained for future reference.
Technical Specification
Parts list Technical Data
1. Long screws 4 pcs Model MODEL 1198  REMOTE
2. Plastic wall plug 4 pcs Voltage AC 220240V Fuse 13 amp
3. Remote Control Unit (Inc Battery) 1 Pc Frequency 50Hz
4. Small Screws 4 pcs Power 1800 2000W
5. Small wall Brackets 2 pcs Lamp LED Unit
6:
Deflector Bracket (Option) 1 pcs
Dimensions
Width 480mm
Height 410mm
Depth 125mm
Fire Installation
Unpack the heater carefully and retain all packaging for future use. Ensure that all packing items are removed and read any warning
labels carefully (see Maintenance Section).
The appliance must be positioned so that the plug is accessible. Only when you are certain that you have completed
the installation should you plug in and switch on at the wall socket.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied
through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
Important Notes
•
These Instructions should be read carefully and retained for the future reference.
• This heater must not be located immediately above a fixed socket outlet.
• Do not use the heater in the immediate surrounds of a bath, a shower, or a swimming pool.
• Do not cover this heater, or obstruct the air inlet or outlet, otherwise there is a risk of overheating.
• The heater must be cooled down completely before any maintenance
• This heater must be fixed against a vertical surface.
• Under no circumstances should the heater be used as a free standing appliance.
• After unpacking, please make sure that the
appliance is intact, with no signs of damage caused by transport. If in doubt, do not
use the appliance and contact the Service Centre.
• During normal operation this appliance will emit noise from the internal fan unit.
• If the supply cord is damaged, i
t must be replaced by the manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of ex
perience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Warning: This appliance must be earthed.
The wires in the mains lead connected to this appliance are coloured in accordance with the following code:
GREEN and YELLOW Earth
BLUE Neutral
Brown Live
As the colour of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
•
The wire which is coloured Green and Yellow must be
connected to the terminal in the plug which is marked with the letter E or
by the earth symbol or coloured Green or Green and Yellow.
• The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.
• The wire which is coloured Brown must be connected to the terminal which is marked with letter L or coloured Red.

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the bemodern 1198 and is the answer not in the manual?

Overview

  1. Function Description
  2. Important Technical Specifications
  3. Usage Features
  4. Installation
  5. Operation (Manual Control)
  6. Operation (Remote Handset)
  7. Safety Precautions
  8. Maintenance Features
  9. General Maintenance
  10. Remote Handset Battery Replacement
  11. Maintenance of Motors
  12. Cleaning the Appliance
  13. Replacing the LED Flame Effect
  14. Safety Thermal Cut-Out (E.S. Control)
  15. Secondary Thermal Fuse Link
  16. Environmental Information

This document provides user instructions for the BeModern Remote Controlled 2kW Rotisserie Effect Fan Heater, a product designed for use as a fireplace or stove accessory. It covers installation, operation, maintenance, and warranty information.

Function Description

The BeModern 2kW Rotisserie Effect Fan Heater is an electric appliance designed to provide both heat and a decorative flame effect. It features a fan heater with two heat settings (1000W and 2000W) and a rotisserie-style flame effect with adjustable intensity. The unit can be operated via both manual controls on the appliance and a multifunction infrared remote handset. It also includes a backlight feature with four settings (OFF, YELLOW, BLUE, and MIX) to enhance the visual appeal. The heater is equipped with a thermostat for temperature control and safety features such as a thermal cut-out to prevent overheating. It is designed for wall-mounted installation and must be earthed.

Important Technical Specifications

  • Model: MODEL 1198 - REMOTE
  • Voltage: AC 220-240V
  • Frequency: 50Hz
  • Power: 1800-2000W (2kW)
  • Fuse: 13 amp
  • Lamp: LED Unit
  • Dimensions:
    • Width: 480mm
    • Height: 410mm
    • Depth: 125mm
  • Heat Settings: 1000W (LOW) and 2000W (HIGH)
  • Flame Effect: Rotisserie style with adjustable intensity (HIGH, MEDIUM, LOW)
  • Backlight Settings: OFF, YELLOW, BLUE, MIX
  • Remote Control Range: Up to 4 meters or 13 feet
  • Safety Features: Thermal cut-out (E.S. Control) and secondary thermal fuse link.
  • Compliance: European Safety Standards (LVD) EN60335-2-30 and European Electro Magnetic Compatibility (EMC) En55015, EN60555-2 and EN60555-3.

Usage Features

Installation:

The heater is designed for wall-mounted installation. It comes with wall brackets, screws, and wall plugs. A template is provided to assist with drilling the fixing positions, ensuring minimum clearance distances are maintained (200mm minimum from ceiling, 200mm minimum from sides, 375mm minimum from floor without deflector bracket, 180mm minimum from shelf with deflector bracket). The appliance must be fixed against a vertical surface and not used as a free-standing unit. It is crucial to use appropriate fixings strong enough to support the weight of the fire and front panel. The lower support brackets must always be used to prevent the heater from lifting. The appliance must be positioned so that the plug is accessible.

Operation (Manual Control):

  • MANUAL ON/OFF SWITCH: Located on the left-hand side, this switch turns the heater on/off and enables/disables the use of remote and panel push buttons.
  • FLAME BUTTON: Cycles through three flame effects with each press.
  • HEATER BUTTON: Press once for 1000W power, press again for 2000W power.
  • THERMOSTAT SETTING: A knob marked with numbers (1-9) controls the temperature. Start at setting 9 and turn left to decrease temperature, or right to increase. The thermostat maintains the room at the selected level.

Operation (Remote Handset):

Ensure the master on switch (manual on/off switch) is in the 'ON' (I) position and batteries are correctly installed in the remote control.

  • POWER BUTTON: Turns the flame effect settings to the last used setting.
  • FLAME BUTTON: Changes the intensity of the flame illumination, cycling between HIGH, MEDIUM, and LOW settings.
  • BACKLIGHT BUTTON: Cycles through the four backlight settings: OFF, YELLOW, BLUE, and MIX.
  • LOW BUTTON: Activates the 1KW heat setting. Pressing it again turns off the heating.
  • HIGH BUTTON: Activates the 2KW heat setting. Pressing it again turns off the heating.
  • Heat Output Adjustment: Use the LOW and HIGH buttons to select desired heat output.
  • Cold Air Blow: When the heater is turned on, there will be a brief period (approx. 6 seconds) where cold air blows to clear elements of debris. Similarly, after switching off, the fan will blow cold air to re-cool the elements before turning off.

Safety Precautions:

  • Do not locate the heater immediately above a fixed socket outlet.
  • Do not use in the immediate surrounds of a bath, shower, or swimming pool.
  • Do not cover the heater or obstruct air inlet/outlet to prevent overheating.
  • The heater must be cooled down completely before any maintenance.
  • The appliance must be earthed.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised. Children should be supervised not to play with the appliance.
  • To avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device (e.g., timer) or connected to a circuit that is regularly switched on and off by the utility.
  • Do not operate the unit if it is damaged or has malfunctioned; contact a qualified service technician.

Maintenance Features

General Maintenance:

  • Before any maintenance or cleaning, disconnect the appliance from the main supply.
  • Only competent persons should service/repair appliances.
  • Periodic cleaning/vacuuming of the fan/heater unit is recommended.

Remote Handset Battery Replacement:

  • Replace with two AAA batteries. Ensure correct installation.

Maintenance of Motors:

  • The motors for the fan and flame effect are pre-lubricated for extended bearing life and do not require further lubrication.

Cleaning the Appliance:

  • Exterior: Clean with a soft, damp, lint-free cloth. Do not use cleaning or polishing products.
  • Front Glass Panel: To remove fingerprints or marks, use a soft, damp, lint-free cloth with a good quality household glass cleaner. The panel should be completely dried with a clean, lint-free cloth or paper towel.
  • Caution: Do not use abrasive cleaners on the glass panel. Do not spray liquids directly onto any surface of the unit.

Replacing the LED Flame Effect:

  • The LED lighting is designed to last the lifetime of the unit. If replacement is required, it should only be performed by a qualified electrician.

Safety Thermal Cut-Out (E.S. Control):

  • This device switches off the fire if it overheats.
  • To reset: Switch off the appliance, unplug from the wall socket, and leave for 5-10 minutes to cool down. Plug in and switch on; the E.S. Control will reset.
  • If the E.S. Control switches off again, have the appliance checked by a competent electrician.
  • This fuse link is incorporated into the heating element and breaks the electrical circuit if the heater fan fails. Unlike the E.S. Control, this link cannot be reset. If it breaks, the appliance must be checked by a competent electrician, and the fan/element replaced.

Environmental Information:

  • Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities. Contact your local authority for information on collection systems. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance free of charge.

bemodern 1198 Specifications

General IconGeneral
Brandbemodern
Model1198
CategoryHeater
LanguageEnglish