UE Declaration of Conformity/Incorporation (DoC/DoI)
Manufacturer's name: Automatismi Benincà SpA
Address: Via Capitello, 45 - 36066 Sandrigo (VI) - Italia
Telephone: +39 0444 751030
Email address: sales@beninca.it
Person authorised to draft the technical documentation: Automatismi Benincà SpA
Product type: Electromechanical actuator 24V DC for swing gates
Model/type: KMB24
Accessories: LAMPI24.LED - PUPILLA - TO.GO WV - TOKEY
The undersigned Luigi Benincà, as the Legal Officer, declares under his liability that the aforementioned product complies with the provi-
sions established by the following directives:
Directive 2014/30/UE OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26 February 2014, on the harmonisation of the
laws of Member States relating to electromagnetic compatibility, according to the following harmonised regulations:
EN 61000-6-2:2005 + AC:2005, EN 61000-6-3:2007 + A1:2011.
Directive 2011/65/EU of the European Parliament and Council, dated 8 June 2011, on the restricted use of certain hazardous substances in
electrical and electronic devices (RoHS), according to the following standards:
EN 50581:2012
Directive 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9 1999 regarding radio devices and terminal
and telecommunications devices and the reciprocal recognisances of their conformity, according to the following concurred regulations:
ETSI EN 301 489-3 V1.4.1 (2002) + ETSI EN 301 489-1 V1.4.1 (2002) + ETSI EN 300 220-3 V1.1.1 (2000) + EN 60950-1 (2001)
Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 17 May 2006, on machinery, which amends
Directive 95/16/EC, and complies with the requisites for the “partly completed machinery (almost machinery)” set forth in the EN13241-
1:2003 regulation.
EN 60335-1:2012 + A11:2014; EN 60335-2-103:2015.
• The manufacturer declares that the pertaining technical documentation has been drawn up in compliance with Attachment VII B of the
2006/42/ EC Directive and that the following requirements have been complied with:
1.1.1 - 1.1.2 - 1.1.3 - 1.1.5 - 1.2.1 - 1.2.3 - 1.2.6 - 1.3.1 - 1.3.2 - 1.3.3 - 1.3.4 - 1.3.7 - 1.3.9 - 1.5.1 - 1.5.2 - 1.5.4 - 1.5.5 - 1.5.6 - 1.5.7 - 1.5.8
- 1.5.10 - 1.5.11 - 1.5.13 - 1.6.1 - 1.6.2 - 1.6.4 - 1.7.2 - 1.7.4 - 1.7.4.1 - 1.7.4.2 - 1.7.4.3.
• The manufacturer undertakes that information on the “partly completed machinery” will be sent to domestic authorities. Transmission
ways are also included in the undertaking, and the Manufacturer’s intellectual property rights of the “almost machinery” are respected.
• It is highlighted that commissioning of the “partly completed machinery” shall not be provided until the final machinery, in which it should
be incorporated, is declared compliant, if applicable, with provisions set forth in the Directive 2006/42/EC on Machinery.
• Moreover, the product, as applicable, is compliant with the following regulations:
EN 12445:2002, EN 12453:2002, EN 12978:2003
Benincà Luigi, Legal Officer.
Sandrigo, 08/02/2016.
The certificate of conformity in this document corresponds to the last review available at the time of printing and could differ for editorial
requirements from the original available from the manufacturer.
The most recent and complete certificate of conformity is available consulting the site: www.beninca.com or can be requested from:
Automatismi Benincà SpA - Sandrigo VI - ITALY.
To Next Page
Loading...
