30
PROGRAMMING
The various functions are programmed using the LCD display on the control panel and by setting the desired values in the programming
menus described below.
The parameters menu allows a numerical value to be set to a function, similar to an adjustment trimmer.
The logic menu allows a function to be activated or deactivated, similar to the setting of a dip-switch.
Other special functions follow the parameters and logic menus and may vary depending on the type of control panel or software revi-
sion.
TO ACCESS PROGRAMMING
1 - Press the <PG> button to display the first “PAR” parameter menu.
2 - Choose the menu with the button <#> or <$> that you intend selecting.
3 - Press the <PG> button, the display shows the first function available on the menu.
4 - Choose the function with the button <#> or <$> that you intend changing.
5 - Press the <PG> button to display the value currently set for the selected function.
6 - Select the menu with the button <#> or <$> that you intend assigning to the function.
7 - Press the <PG> button to display the “PRG” signal indicating successful programming.
NOTES
Pressing the key <#> with the display off is the same as pressing the Step-step button.
Simultaneous pressing of <#> and <$> executed in a function menu allows you to return to the higher menu without making changes.
Keep the key <#> or key <$> pressed to accelerate the increase/decrease of the values.
After 60s standby, the control panel exits programming mode and the display switches off.
INSTALLATION
The AUTOSET procedure is described below:
1) Power the control unit.
2) Manually unlock, check the manoeuvre of the door is smooth and friction-free.
3) Manually bring the door to the desired opening position, adjust the cam of the opening limit switch, the display segment switches
on to signal intervention of the micro-switch.
4) Close the door and lock again.
5) Press the PG button, then twice press the button UP <#> to display the AUTO function, press PG to select, the AUTO writing
flashes, press PG to confirm.
6) The display shows the writing 1 MOT or 2 MOT according to the number of motors connected to the control unit, if the number of
motors is correct, confirm with PG.
7) The message UP is displayed, press the button UP <#> and keep it pressed to reach the complete opening position (intervention
of the opening limit switch).
8) Press the PG button, the control panel controls a CLOSING>OPENING>CLOSING manoeuvre, during which the display shows the
message CLOSE>OPEN>CLOSE at the end of which the message OK is displayed and the control unit returns to the AUTO menu.
Simultaneously pressing the keys # and $ you exit the programming phase.
9) The procedure has terminated and the control unit has saved the optimal operating parameters
Notes:
- during the programming phase, the courtesy light works in low intensity mode.
- during the entire AUTOSET phase, the red LED flashes.
- adjustment of the opening position takes place in MANNED mode.
- if necessary, you can exit programming by simultaneously pressing keys # and $ or waiting 30 seconds (time-out).
- If the “ERR” error messages appears during the AUTOSET phase, see the “Error messages” paragraph.
ARC TRANSMITTERS
IMPORTANT, PLEASE READ CAREFULLY:
The radio receiver in this product is exclusively compatible with ARC (Advanced Rolling Code) transmitters which, thanks the 128-bit
coding, guarantee higher anti-copying security.
Memorisation of new ARC transmitters is very similar to that of normal Rolling Code transmitters with HCS code.
PARAMETERS, LOGICS AND SPECIAL FUNCTIONS
The following tables describe the functions available on the control unit.
8.4.1) PARAMETERS (PAR)
MENU FUNCTION
MIN-MAX-
(Default)
MEMO
TCA
Automatic closure time Active only with “TCA”=ON logic.
At the end of the time set, the control panel commands a closure manoeuvre.
3-240-(40s)
fsto
Adjusts the manoeuvre speed during the OPENING phase* 50-99-(80%)
fstc
Adjusts the manoeuvre speed during the CLOSING phase* 50-99-(60%)
sldo
Adjusts the speed during the OPENING slowing phase* 10-50-(30%)
sldc
Adjusts the speed during the CLOSING slowing phase*. 10-50-(30%)
TSMO
Adjusts the duration during the OPENING slowing phase* 1-99-(10%)
To Next Page
Loading...
