How to fix BenQ MS500 that does not turn on?
If your BenQ Projector doesn't turn on, first ensure the power cord is securely plugged into both the projector's AC power jack and a working power outlet, checking that the outlet switch is on. Also, if the projector is cooling down, wait for the process to complete before attempting to power it on again.
What to do if my BenQ Projector has no picture?
If you have no picture on your BenQ Projector, make sure the video source is turned on and correctly connected. Check the connection between the projector and the input signal device. Select the correct input signal using the SOURCE key on the projector or remote control. Finally, ensure the lens cover is open.
How to fix blurred image on BenQ MS500?
If you're experiencing a blurred image with your BenQ Projector, try these steps: 1. Adjust the focus of the lens using the focus ring. 2. Adjust the projection angle, direction, and height of the projector to properly align it with the screen. 3. Ensure the lens cover is open.
Why does not BenQ MS500 remote control work?
If the remote control for your BenQ Projector isn't working, try the following: * Replace the battery with new ones. * Remove any obstacles between the remote control and the projector. * Ensure you are within 8 meters (26 feet) of the projector.
General| Projection distance | 0.61 - 7.62 m |
|---|---|
| Vertical scan range | 48 - 120 Hz |
| Horizontal scan range | 31 - 99 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 4000:1 |
| Screen size compatibility | 24 - 300 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | 40 ° |
| Audio input | 1 |
| Aspect ratio | 4:3 |
| Dimensions (WxDxH) | 287 x 232 x 100 mm |
| Connectivity technology | Wired |
| Focus | Manual |
| Throw ratio | 1.86 - 2.04:1 |
| Zoom capability | Yes |
| Focal length range | 21 - 23.1 mm |
| Lamp power | 220 W |
| Light source type | Lamp |
| Service life of light source | 4500 h |
| Service life of light source (economic mode) | 6000 h |
| DVI port | No |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Component video (YPbPr/YCbCr) in | 0 |
| Supported video modes | 1080i, 1080p, 480i, 480p, 576i, 576p, 720i, 720p |
| Analog signal format system | NTSC, PAL, SECAM |
| Supported graphics resolutions | 1600 x 1200 (UXGA), 640 x 480 (VGA), 800 x 600 (SVGA) |
| RMS rated power | 2 W |
| Placement | Ceiling |
| Product type | Standard throw projector |
| Product color | Black, Grey |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 1 W |
| Power consumption (typical) | 297 W |
| Noise level | 33 dB |
| Noise level (economic mode) | 27 dB |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Cables included | VGA |
Weight and Dimensions| Weight | 2500 g |
|---|
Explains how to determine the correct distance for optimal image size.
Details how to connect various video source devices to the projector.
Guides users through the initial power-on and setup process of the projector.
Provides instructions on adjusting image projection angle, auto-adjustment, and fine-tuning.
Explains how to navigate and use the projector's On-Screen Display (OSD) menus.
Describes how to select and switch between different input signal sources.
Guides users on optimizing image quality using wall color and picture modes.
Detailed steps for properly powering off the projector and direct power off.
Lists causes and remedies for the projector failing to power on.
Troubleshooting steps for when no image is displayed on the screen.
Technical details including optical, electrical, and mechanical specifications.
To Next Page
