Why my BenQ Projector does not turn on?
If your BenQ Projector does not turn on, ensure the power cord is properly plugged into both the projector's AC power jack and the power outlet. If the outlet has a switch, make sure it's on. Also, if the projector is cooling down, wait until the process is complete before attempting to turn it on again.
How to fix a BenQ MS560 Projector remote control that is not working?
If the remote control for your BenQ Projector isn't working, first replace both batteries with new ones. If that doesn't solve the problem, make sure there are no obstacles between the remote and the projector. Finally, ensure you are within 8 meters (26 feet) of the projector.
What to do if my BenQ Projector has no picture?
If your BenQ Projector shows no picture, here are a few things to check: * Ensure the video source is on and the signal cable is correctly connected. * Verify the projector is correctly connected to the input signal device. * Select the correct input signal using the SOURCE key. * Make sure the lens cover is open.
How to fix a blurred image on a BenQ Projector?
If the image from your BenQ Projector appears blurred, try these steps: 1. Adjust the focus of the lens using the focus ring. 2. Adjust the projection angle, direction, and height of the projector to properly align it with the screen. 3. Ensure the lens cover is open.
General| Number of colors | 1.073 billion colors |
|---|---|
| Native aspect ratio | 4:3 |
| Projection distance | - m |
| Vertical scan range | 23 - 120 Hz |
| Horizontal scan range | 15 - 102 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 20000:1 |
| Screen size compatibility | 60 - 150 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | -40 - 40 ° |
| Light source type | Lamp |
| Service life of light source | 6000 h |
| Service life of light source (economic mode) | 10000 h |
| Offset | 110 % |
| Throw ratio | 1.96 - 2.15 |
| Focal length range | - mm |
| Full HD | Yes |
| Supported video modes | 480i, 480p, 576i, 576p, 720p, 1080i, 1080p |
| Analog signal format system | NTSC, PAL, SECAM |
| Supported graphics resolutions | 640 x 480 (VGA), 1920 x 1200 (WUXGA) |
| DVI port | No |
| HDMI connector type | Full-size |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Component video (YPbPr/YCbCr) in | 0 |
| Noise level | 34 dB |
| Number of OSD languages | 30 |
| Noise level (economic mode) | 29 dB |
| On Screen Display (OSD) languages | ARA, BUL, CHI (SIMPL), CHI (TR), CRO, CZE, DAN, DEU, DUT, ENG, ESP, FAS, FIN, FRE, GRE, HIN, HUN, IND, ITA, JPN, KOR, NOR, POL, POR, RUM, RUS, SWE, THA, TUR, VIE |
| RMS rated power | 10 W |
| Placement | Ceiling |
| Product type | Standard throw projector |
| Product color | White |
| Market positioning | Business |
| Cable lock slot type | Kensington |
| Power source | AC |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (max) | 280 W |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 260 W |
| Power consumption (economy mode) | 215 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Cables included | AC, VGA |
| Remote control type | IR |
| Quantity per pack | 1 pc(s) |
| Harmonized System (HS) code | 85286200 |
Weight and Dimensions| Depth | 221 mm |
|---|---|
| Width | 296 mm |
| Height | 120 mm |
| Weight | 2300 g |
Outlines the terms and conditions of the product's limited warranty coverage.
States the copyright holder and restrictions on reproducing or distributing the manual.
Specifies limitations and disclaimers regarding the content and warranties.
Provides information or links related to BenQ projector patent coverage.
Classifies the projector as Risk Group 2 for photobiological safety and related warnings.
Lists all standard and optional accessories included with the projector.
Details additional accessories available for purchase to enhance projector functionality.
Step-by-step guide for replacing batteries in the projector's remote control.
Describes the power button, power indicator, and temperature/light warning indicators.
Details the IR remote sensor's location and the use of navigation buttons.
Explains how to access menus, select sources, and use general function buttons.
Covers controls for picture adjustments, aspect ratio, light modes, and quick setup.
Factors to consider when selecting an installation site for the projector.
Pre-installation checks and recommendations for safe projector mounting.
How to correct trapezoidal distortion by adjusting the projector's feet.
Using the auto-adjustment feature for optimizing picture quality.
Adjusting image size with the zoom ring and sharpness with the focus ring.
Details on how to connect and manage audio input and output for the projector.
Step-by-step instructions for powering on and starting the projector.
Guidance on using a security cable lock to prevent projector theft.
Instructions for setting, changing, and disabling the projector's password lock function.
Procedure for properly powering off the projector and its cooling process.
Information on powering off the projector directly and subsequent restart precautions.
Explains the functions and options available in the projector's basic OSD menu.
Details the comprehensive functions and settings available in the advanced OSD menu.
Adjusts the image brightness level for optimal viewing.
Sets how the image is scaled to fit the screen based on input signal.
Selects predefined picture modes for different viewing environments.
Adjusts the audio output level of the projector.
Configures lamp power modes to balance brightness and extend lamp life.
Displays system status, resolution, source, and lamp usage time.
Covers adjustments for picture mode, brightness, contrast, color, and other visual parameters.
Covers settings related to aspect ratio, keystone correction, test patterns, and positioning.
Configuration options for 3D display and HDMI signal formats.
Features for digitally zooming the image and resetting display settings.
Settings for projector installation type and remote receiver enablement.
Configuration for automatic signal detection and source synchronization.
Adjustments for lamp modes, timers, and cooling functions.
Guidance on using the projector in high altitude environments and its implications.
Settings controlling power on/off behavior, auto power off, and instant restart.
Options for panel key lock, password protection, and baud rate configuration.
Settings for RS-232 communication and HDMI signal equalization.
Selection of OSD language and configuration of standby mode behavior.
Customization of background splash screen and OSD menu display.
Configuration for audio output, volume, and closed captioning features.
Options to restore system settings to factory defaults.
Shows detected input signal resolution and the current active source.
Displays the selected picture mode and light mode settings.
Shows the projector's lamp usage time and firmware version.
Instructions for cleaning the projector lens and case to ensure optimal performance.
Guidelines for safely storing and transporting the projector.
Details on lamp usage, extending lamp life, and replacing the lamp.
Methods to prolong the projector lamp's lifespan through mode selection.
Information on when to replace the projector lamp and potential issues.
Detailed steps for replacing the projector lamp, emphasizing safety precautions.
Procedure to reset the projector's lamp usage timer after replacement.
Describes the projector's status indicated by the power LED.
Interprets the status indicated by the light LED, including lamp life.
Explains error conditions indicated by temperature and fan LEDs.
Solutions for problems related to the projector not turning on or displaying a picture.
Troubleshooting steps for blurred images and non-functional remote controls.
Guidance on resolving issues when an incorrect password is entered.
Details on resolution, display system, lamp, power supply, and consumption.
Information on weight, dimensions, and control interfaces like USB and RS-232.
Lists all available input and output ports on the projector.
Specifies operating and storage conditions for the projector.
Table detailing vertical, horizontal, and pixel frequencies for PC inputs.
Table detailing supported timings for HDMI inputs, including 3D formats.
Lists supported timings for Video, S-Video, and Component-YPbPr inputs.
To Next Page
