What to do if my Bernina 555 QE speed is too low?
If the sewing speed is too low, it could be due to unfavorable room temperature; place the machine in a warm room one hour before use. Alternatively, check and adjust the sewing speed settings in the Setup Program.
What to do if the BSR presser foot #42 is not detected by my Bernina 555 QE Sewing Machine?
If the BSR presser foot #42 is not being detected, first clean the lens with a soft, slightly damp cloth. Also, ensure the BSR cable is correctly inserted vertically until you feel it click into place.
Why does my Bernina 555 QE keep breaking the upper thread?
If the upper thread breaks frequently, several factors could be at play. First, ensure that your needle and thread are a compatible match. If the upper thread is too tight, reduce the tension. Rethread the machine to rule out threading errors. Use only quality thread to prevent breakage. If the stitch plate or hook tip is damaged, contact a specialized BERNINA dealer for repairs. Also, check the thread take-up lever area for any caught thread; remove the headframe, clear any remnants, and reattach it.
Why is my Bernina 555 QE Sewing Machine breaking the lower thread?
Lower thread breakage can occur if the bobbin case is damaged, in which case you should replace it. If the stitch hole in the stitch plate is damaged, contact a specialized BERNINA dealer for repairs. Also, ensure the needle isn't blunt or bent; replace it if necessary.
What causes faulty stitching on a Bernina Sewing Machine?
Faulty stitching can be caused by a few things. Check for thread remnants between the thread tension discs and remove them by folding a piece of thin material and sliding the folded edge between the discs. Ensure the machine is correctly threaded. Also, inspect for thread remnants below the bobbin case spring and remove them.
Why does my Bernina 555 QE Sewing Machine needle keep breaking?
A broken needle can result from several issues. Ensure the needle is correctly inserted with the flat side to the back and pushed fully into the needle holder before tightening the screw. Avoid pulling the fabric; instead, feed it evenly. For thick fabrics, use an appropriate presser foot like Jeans foot No. 8. Also, be sure to use quality thread to prevent knotted thread from causing the needle to break.
Why aren't the sewing light and free arm light working on my Bernina 555 QE?
If neither the sewing light nor the light on the free arm lights up on your Bernina sewing machine: * Check the settings in the Setup Program; activate it in the Setup Program. * If the sewing light is defective, contact the specialized BERNINA dealer.
What to do if my Bernina 555 QE is skipping stitches?
If your Bernina sewing machine is skipping stitches, consider these possible causes: * The needle may be incorrect; use the needle system 130/705H. * The needle might be blunt or bent; replace the needle. * You might be using a poor-quality needle; use a new BERNINA quality needle. * The needle may be incorrectly inserted; insert the needle with the flat side to the back as far up as it will go into the needle holder and tighten the screw. * The needle point may be incorrect; match the needle point to the texture of the material.
How to fix uneven stitches on my Bernina 555 QE?
Uneven stitch formation can occur for several reasons. Check the upper thread tension and adjust if it's too tight or loose. Replace the needle, ensuring you're using a new, high-quality BERNINA needle. Also, verify you're using quality thread and that the needle and thread are correctly matched. Ensure the machine is correctly threaded. Avoid pulling the fabric; instead, feed it evenly. Finally, confirm that you are using the bobbin case marked with the triangle.
How to fix error during software update on Bernina 555 QE Sewing Machine?
If you encounter an error during a software update on your Bernina sewing machine: * If the USB stick is not recognized, use a BERNINA USB stick. * If the update process is blocked and the hourglass on the display is inactive, remove the USB stick. * If the date of the software update cannot be found, switch the machine off.
General| Type | Electronic Sewing Machine |
|---|---|
| Maximum Stitch Width | 5.5 mm |
| Maximum Stitch Length | 5 mm |
| Display | LCD |
| Free Arm | Yes |
| Feed Dog | Adjustable |
| Speed | 900 stitches per minute |
| Memory | Yes |
| Start/Stop Button | Yes |
| Needle Threader | Automatic |
| Automatic Thread Cutter | Yes |
| Presser Feet | Included |
| Warranty | 2 years |
| Weight | 9.5 kg |
To Next Page
