What to do if my Bernina 590 stitch width is not adjustable?
If the stitch width is not adjustable, it may be because the selected needle and stitch plate cannot be used in combination. In this case, replace the needle and stitch plate.
Why does the upper thread keep breaking on my Bernina Sewing Machine?
If the upper thread keeps breaking on your Bernina sewing machine, consider the following: * The needle and thread combination might be incorrect; match the needle with the thread size. * The upper thread may be too tight; reduce the upper thread tension. * The machine might be incorrectly threaded; rethread it. * The thread quality could be poor; use quality thread. * The stitch plate or hook tip may be damaged; contact a specialized BERNINA dealer for repairs. * The thread may be caught in the area of the thread take-up lever; replace the stitch plate.
How to fix error during software update on Bernina Sewing Machine?
If you encounter an error during a software update on your Bernina sewing machine: * If the USB stick is not recognized, use a BERNINA USB stick. * If the update process is blocked and the hourglass on the display is inactive, remove the USB stick. * If the date of the software update cannot be found, switch the machine off.
How to fix uneven stitches on my Bernina Sewing Machine?
Uneven stitch formation can occur due to several reasons. First, adjust the upper thread tension, as it might be too tight or too loose. Replace the needle, ensuring you use a new BERNINA quality needle, as a blunt or bent needle can cause this issue. Also, poor quality thread or an incorrect needle/thread combination can lead to uneven stitches, so use quality thread and match the needle with the thread size. Rethread the machine to ensure it's correctly threaded. Make sure you feed the fabric evenly instead of pulling it. Finally, ensure you are using the correct bobbin case marked with the triangle.
Why is the upper thread breaking on my Bernina Sewing Machine?
If the upper thread is breaking, consider these potential causes. Ensure you match the needle with the thread size, as an incorrect needle/thread combination can cause breakage. Reduce the upper thread tension if it is too tight. Rethread the machine to rule out threading errors. Use quality thread to avoid breaks caused by poor thread. If the stitch plate or hook tip is damaged, contact a specialized BERNINA dealer for repairs. Also, check for thread caught in the area of the thread take-up lever; slide the headframe to the left to remove it, clear any thread remnants, then reattach the headframe by inserting the knobs into the notches and sliding it to the right.
Why is my Bernina 590 Sewing Machine needle breaking?
A needle can break for several reasons. Ensure the needle is correctly inserted with the flat side to the back, as far up as it will go into the needle holder, and tighten the screw. Avoid pulling the fabric; feed it evenly. If sewing thick fabric, use the appropriate presser foot, such as Jeans foot No. 8. Finally, use quality thread to avoid breaks caused by knotted thread.
How to resolve faulty stitching on my Bernina 590 Sewing Machine?
Faulty stitching on your Bernina sewing machine can often be resolved by checking for these issues: * Thread remnants between the thread tension discs; fold a piece of thin material and slide the folded edge (not the raw edges) between the thread tension discs. * The machine may be incorrectly threaded; rethread it. * Thread remnants below the bobbin case spring; remove the thread remnants under the spring.
Why is my Bernina 590 Sewing Machine speed too low?
If the sewing speed is too low, it could be due to an unfavorable room temperature; place the machine in a warm room one hour before use. Alternatively, adjust the sewing speed in the Setup Program, as the settings there may be affecting it.
What to do if the BSR presser foot #42 is not detected on my Bernina 590 Sewing Machine?
If the BSR presser foot #42 is not being detected, try these solutions. Clean the lens with a soft, slightly damp cloth. Ensure the BSR cable is correctly inserted by inserting the BSR connector vertically until you feel it click into place.
What to do if I get an error during a software update on my Bernina Sewing Machine?
If you encounter an error during a software update, try the following steps. Use a BERNINA USB stick. If the update process is blocked with an inactive hourglass, remove the USB stick. Switch the machine off and then on again. Follow the instructions on the display. Ensure you unzip the update data and save the software update data directly onto the USB stick, not in a file.
General| Stitch Width | 9 mm |
|---|---|
| Sewing Speed | 1000 stitches per minute |
| Color Touch Screen | Yes |
| Hook System | Bernina Hook |
| USB Interface | Yes |
| Needle Positions | 11 |
| Stitch Length | 6 mm |
| Memory (Short-Term / Altered Stitches) | Yes |
| Basting | Yes |
| Bobbin winding while sewing | Yes |
| Needle Stop Up/Down | Yes |
| Drag and Drop | Yes |
| Bobbin Thread Sensor | Yes |
| Bernina Stitch Regulator (BSR) | Optional |
| Start/Stop Button | Yes |
| Slide Speed Control | Yes |
| Automatic Thread Cutter | Yes |
| Speed Control | Yes |
| LCD Screen | Yes |
| Built-in Memory | Yes |
| Upper Feed | Dual Feed |
| Type | Sewing and Embroidery Machine |
| Presser Feet | Included |
| Total Number of Stitches | 1774 |
To Next Page
