Bestway 58497 User Manual (English)

Other manuals for Bestway 58497

Questions and Answers:

Z
zyoungAug 14, 2025
Why is there no water flow in my Bestway Water Filtration System?
- A
  amanda17Aug 14, 2025
  There might be several reasons for the lack of water flow. First, check if the stopper plugs were removed and the debris screens were inserted. Second, ensure that any trapped air has been released. Third, verify that the control valve is set to the filter function, not closed. Also, the strainer might be blocked and needs cleaning. In some cases, the sand filter might be broken, requiring professional service.
D
Daniel BowmanAug 17, 2025
Why is my Bestway Water Filtration System showing excessive filter pressure?
- S
  Samantha VazquezAug 18, 2025
  Excessive filter pressure can occur due to a dirty filter, which requires backwashing. Another cause may be a calcified sand bed, which means you should inspect the sand and change it if necessary. Insufficient backwashing could also be the reason; backwash until the water runs clear. Lastly, the pressure gauge might be broken and needs replacement.
K
kelly21Aug 21, 2025
What to do if sand is flowing to the pool from my Bestway 58497 Water Filtration Systems?
- J
  Jeremy ReevesAug 21, 2025
  If sand is flowing into the pool, the sand might be too small; it is recommended to use 0.45 mm to 0.85 mm #20 silica sand. Also, check if the sand level is too high, ensuring it's between the 'MAX' and 'MIN' markings on the collector hub. Finally, inspect the skimmer; if it's broken, replace it.
A
Amber GarrettAug 25, 2025
What to do if connectors leak in Bestway 58497?
- H
  Heather AliAug 26, 2025
  If the connectors are leaking, first check if the connector's washer is correctly placed; reposition it if necessary. If the washer is broken, replace it. Also, ensure that the hoses are not loose and tighten them.
A
Adam CoxAug 28, 2025
What to do if the control valve leaks from the port D in Bestway 58497?
- T
  Teresa MullenAug 28, 2025
  If the control valve leaks from port D, ensure that the control valve is set to only one function, not between two. If the problem persists, the gasket may be broken and needs replacement.
A
andrew61Sep 1, 2025
What to do if the pressure is excessive in my Bestway Water Filtration System?
- P
  Patrick LeSep 1, 2025
  Excessive filter pressure can stem from several causes. Try backwashing the filter first, as the filter might be dirty. Inspect the sand bed for calcification and replace the sand if needed. Also, ensure you are backwashing sufficiently until the water runs clear. If the problem persists, the pressure gauge might be broken and require replacement.
V
vmorganSep 5, 2025
How to stop sand flowing to the pool from my Bestway Water Filtration System?
- A
  Adrian RiversSep 5, 2025
  If sand is flowing into your pool, it could be due to several reasons. The sand might be too small; it's recommended to use 0.45 mm to 0.85 mm #20 silica sand. The sand level might be too high; check if it's between the 'MAX' and 'MIN' markings on the collector hub. Lastly, the skimmer could be broken, in which case you should replace it.
M
mmillerSep 9, 2025
What to do if the control valve leaks from port D in my Bestway Water Filtration System?
- J
  Jose HensleySep 9, 2025
  If the control valve is leaking from port D, it might be set between two functions; ensure it is set to only one function. Alternatively, the gasket could be broken and need replacement.

Bestway 58497 Specifications

General

Brand	Bestway
Model	58497
Pump Type	Electric
Power Supply	220-240V
Frequency	50Hz
Flow Rate	7571 l/h
Compatibility	Suitable for above ground pools with a capacity of 1, 100 - 54, 500 L