EasyManua.ls Logo

BIEMMEDUE 162900 - User Manual

BIEMMEDUE 162900
35 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FDV
Powerheater GE 46
Art.nr.: 162900
EAN: 7050481629002
Powerheater GE 46 er en meget effektiv og driftssikre byggvarmer, som kan fyres med diesel
eller parafin. GE 46 har en solid ramme med kjørehåndtak i pulverlakkert stål for å tåle et røft
miljø. Store solide hjul gjør modellen lett å transportere. GE 46 er utrustet med Danfoss
dieselpumpe, fotoelektrisk flammevakt og sikkerhetstermostat med manuell reset.
Brennkammeret på GE 46 er produsert i AISI430 rustfritt stål. Dette gir maksimal levetid. GE
46 kan tilkoples romtermostat og ekstern dieseltank. De passer for tørking av bygninger,
byggeplasser og for oppvarming av små og mellomstore arealer.
Teknisk data
Dimensjoner lxbxh (mm): 1075x440x630
FomaNorgeAS

Table of Contents

Questions and Answers

  • J
    Jennifer HarmonAug 16, 2025
    What to do if my BIEMMEDUE 162900 fan starts and flame lights, generating fumes?
    • J
      Jeremiah HallAug 16, 2025
      If the fan starts, the flame lights, and it generates fumes, there might be several causes: * Insufficient combustion air: Make sure the air inlet and outlet are free. * Excess combustion air: Check the position of the air regulation ring. * Fuel contaminated or contains water: Drain the fuel tank and load it with clean fuel. * Air leaks in the fuel circuit: Check the seals on the ducts and the diesel filter. * Excess fuel at the burner: Check the pump pressure.
  • J
    Julie HerreraAug 19, 2025
    What to do if my BIEMMEDUE 162900 Heater fan does not start or stops during start-up or heating?
    • S
      Stephanie SteeleAug 19, 2025
      If the fan doesn't start or stops during start-up or heating, here are a few things to check: * No electrical current: Check the mains. * Voltage below 175V: The heater will restart automatically when the voltage exceeds 190 V. * Voltage above 265V: The heater will restart automatically when the voltage is below 250 V.
  • E
    Elijah WarrenAug 22, 2025
    Why my BIEMMEDUE 162900 Heater motor does not start and there is no ignition?
    • A
      Amber GonzalezAug 22, 2025
      If the motor doesn't start and there is no ignition, it could be due to: * Wrong setting of room thermostat or other control: Check the correct setting of the heater control. If it's a thermostat, make sure the selected temperature is higher than the room temperature. * Defective thermostat or other control: Replace the control device.
  • C
    Christopher ValdezAug 25, 2025
    What to do if my BIEMMEDUE 162900 does not stop?
    • S
      Sabrina KennedyAug 26, 2025
      If the heater does not stop, it could be due to a defective solenoid seal. Replace the complete solenoid to resolve this issue.
  • N
    Natasha GarzaAug 28, 2025
    What to do if the BIEMMEDUE 162900 Heater fan stops during start-up or heating?
    • A
      anthonyjimenezAug 28, 2025
      If the fan stops during start-up or heating, consider the following potential issues: * Presence of flame before transformer ignites: Clean and eliminate diesel residue in the combustion chamber. * Defective photocell: Replace the photocell. * Defective electrical motor: Replace the electrical motor. * Defective electrical motor bearings: Replace the electrical motor bearings. * Burned out condenser: Replace the condenser. * Defective electric ignitor: Check the connection of H.T. wires to electrodes and transformer. * Defective flame control box: Replace the control box.
  • B
    brookemarshallSep 3, 2025
    What to do if the BIEMMEDUE 162900 Heater fan starts and flame lights, generating fumes?
    • M
      Molly TaylorSep 3, 2025
      If the fan starts, the flame lights, but it generates fumes, here are some possible causes and solutions: * **Insufficient combustion air:** Make sure the air inlet and outlet are free. * **Excess combustion air:** Check the position of the air regulation ring. * **Fuel contaminated or contains water:** Drain the fuel tank and load it with clean fuel. * **Air leaks in the fuel circuit:** Check the seals on the ducts and the diesel filter. * **Insufficient fuel at burner / Excess fuel at burner:** Check pump pressure.
  • R
    Richard HarrisSep 6, 2025
    What to do if the BIEMMEDUE 162900 fan does not start or stops during start-up or heating?
    • D
      danielkingSep 6, 2025
      If the fan doesn't start or stops, it could be due to several reasons: * **No electrical current:** Check the mains. * **Voltage below 175V:** The heater will restart automatically when the voltage exceeds 190 V. Check the supply voltage. * **Voltage above 265V:** The heater will restart automatically when the voltage is below 250 V. Check the supply voltage.
  • J
    James FisherSep 9, 2025
    Why BIEMMEDUE Heater fan starts and flame lights, generating fumes?
    • J
      james59Sep 9, 2025
      If your BIEMMEDUE Heater's fan starts and the flame lights, but it generates fumes, consider these possible causes: * **Insufficient combustion air:** Ensure that both the air inlet and outlet are unobstructed. * **Excess combustion air:** Check the position of the air regulation ring. * **Fuel contaminated or contains water:** Drain the fuel tank and refill it with clean fuel. * **Air leaks in fuel circuit:** Inspect the seals on the ducts and the diesel filter. * **Insufficient fuel at burner/Excess fuel at burner:** Check pump pressure.
  • B
    Benjamin KingDec 1, 2025
    Why does the BIEMMEDUE Heater fan stop during start-up or heating?
    • D
      Diana PorterDec 1, 2025
      The fan might stop during start-up or heating due to: 1. Presence of flame before the transformer ignites: Clean and eliminate diesel residue in the combustion chamber. 2. A defective photocell: Replace the photocell. 3. A defective electrical motor: Replace the electrical motor. 4. Defective electrical motor bearings: Replace the electrical motor bearings. 5. A burned-out condenser: Replace the condenser. 6. A defective electric ignitor: Check the connection of H.T. wires to electrodes and transformer. 7. A defective flame control box: Replace the control box. 8. Insufficient or no fuel at burner: Check the state of the motor-pump plastic coupling. 9. Defective solenoid or electric ignitor: Check the electrical connection. 10. Internal error of electronic device: Reset the devic...

BIEMMEDUE 162900 Specifications

General IconGeneral
BrandBIEMMEDUE
Model162900
CategoryHeater
LanguageEnglish

Related product manuals