Binks 21 - Nozzle and Needle Selection Chart

NOZZLE AND NEEDLE SELECTION CHARTS
VERY THIN 63ss x 63P PE 4.5 7.5 10.0 5 263
14-16 secs. Zahn 2 Cup 63Bss x 63PB PE 9.0 14.3 20.0 14 263A
Wash primers, dyes, 66ss x 66SD SE 7.9 12.1 — 10.5 265
stains, solvents, 66ss x 66SK SE 11.0 15.2 19.5 13 265
water, inks 63Bss x 200 PI 3.1 5.2 6.4 12 263A
THIN 63Ass x 63P PE 5.1 8.37 12.2 11 263A
16-20 secs. Zahn 2 Cup 66ss x 66SK SE 11.0 15.2 19.5 13 265
Sealer, lacquers, primers, inks, 63Bss x 200 PI 3.1 5.2 6.4 12 263A
lubricants, zinc chromates,
acrylics
MEDIUM
19-30 secs. Zahn 2 Cup 63Bss x 63PB PE 9.0 14.3 20.0 14 263A
Synthetic enamels, varnishes, 66ss x 66SD SE 7.9 12.1 — 11 265
shellacs, fillers, primers, epoxies, 66ss x 66SK SE 11.0 15.2 19.5 13 265
urethanes, lubricants, 63Css x 200 PI 3.1 5.2 6.4 12 263A
wax emulsions, enamels
HEAVY (Cream-like) 67ss x 67PB PE 9.5 14.9 19.5 12 267
Over 28 secs. 68ss x 68PB PE 9.5 14.1 19.1 12 268
No. 4 Ford Cup 67ss x 206 PI 6.0 9.5 13.0 15 267
VERY HEAVY 68ss x 68PB PE 9.5 14.1 19.1 12 268
Texture coatings, 68ss x 206 PI 6.2 9.8 13.2 15 268
Road marking paint 59Ass x 244 PI 7.8 11.5 15.2 12 259
59Bss x 252 PI 7.8 11.5 15.2 6 259
59Css x 262 PI 7.3 11.0 14.7 6 259
68ss x 206 PI 6.2 9.8 13.2 15 268
ADHESIVES
Waterbase white vinyl glues 63Bss x 66SD-3 PE 7.9 12.1 16.2 4 263
Solvent base, neoprenes 67ss x 67PB PE 9.5 14.1 19.1 12 267
(contact cement) 66ss x 66SD-3 PE 7.9 12.1 16.2 10 265
CERAMICS
Similar abrasive materials, glazes, 67VT x 67PD PE 10.0 15.0 20.0 15 267VT
engobes, porcelain enamel 68VT x 68PB PE 9.5 14.1 19.1 12 268VT
BUFFING COMPOUNDS 64VT x 64PA PE 12.1 15.0 21.0 13 264VT
67VT x 67PD PE 10.0 15.0 20.0 15 267VT
CONCRETE CURING 66ss x 200 PI 3.1 5.2 6.4 15 265
COMPOUNDS 67ss x 206 PI 6.0 9.5 13.0 18 267
68ss x 206 PI 6.2 9.8 13.2 20 268
MULTICOLOR PAINTS 66ss x 200 PI 3.1 5.2 — 12 265
67ss x 206 PI 6.0 9.5 — 15 267
TEFLONS 63Ass x 63PB PE 9.0 14.3 20.1 10 263A
66ss x 66SD PE 7.9 12.1 — 7 265
HAMMERS 63ss X 63PB PE 9.0 14.3 — 14 263A
66ss X 63PB PE 9.0 14.3 — 14 265
66ss X 66SD PE 7.9 12.1 — 7 265
WRINKLE ENAMELS 63Css x 63PB PE 9.0 14.3 20.0 10 263A
66ss x 63PB PE 9.0 14.3 20.0 10 265
ZINC RICH COATINGS 66ss x 67PD PE 12.0 18.0 24.0 15 265
67VT x 67PB PE 9.5 14.1 19.1 12 267VT
Note: PE - Pressure External SP - Siphon External PI - Pressure Internal
TYPE OF FLUID FLUID NOZZLE CFM AT MAX. FLUID NEEDLE NOS.
TO BE SPRAYED X AIR TYPE 30 50 70 PATTERN FOR SPRAY GUN
NOZZLES PSI PSI PSI AT 8” MODEL 21
5