Binks 230 - User Manual

SPRAYGUN MATERIAL NOZZLE NEEDLE AIR NOZZLE GROUP
PART N
o
THREAD PART NO CODE BORE PART NO MAT
L
PART NO CODE AIR CONS
N
100104 BSP 200316 71 0.071”,1.8mm 180123 ST ST 200885 66SD1 (16.2) [27.5] 1
100114 BSP 200338 446 0.046”,1.1mm 180100 NYLON 200850 63PB (18.9) [32.1] 1
100124 BSP 200315 60 0.060”,1.5mm 180124 ST ST 200885 66SD1 (16.2) [27.5] 1
100125 BSP 200338 446 0.046”,1.1mm 180117 ST ST 200850 63PB (18.9) [32.1] 1
100126 BSP 200315 60 0.060”,1.5mm 180124 ST ST 200886 66S2 (6.3) [10.7] 1
100135 BSP 200315 60 0.060”,1.5mm 180124 ST ST 200850 63PB (18.9) [32.1] 1
100176 BSP 200328 2086V 0.086”,2.2mm 180111 ST ST/ 200865 67SA (18.2) [30.1] 4
100188 BSP 200316 71 0.071”,1.8mm 180123 ST ST 200885 66SD1 (16.2) [27.5] 1
Operation Manual:
MODEL 230 PRESSURE/SIPHON FEED
HAND GUN
Important:
Read and follow all instructions and SAFETY PRECAUTIONS
before using this equipment
This is a production hand spray gun suitable for use with most solvent based coating materials. The performance of this gun is
achieved by a range of air nozzles combined with large, smooth flowing air passages and an oversize air valve which gives a lower
pressure drop. The gun is designed to be used with a siphon cup or material feed hose.
IMPORTANT:
These guns are not designed for use with highly corrosive or highly abrasive coating material and if used with such
materials it must be expected that the need for thorough cleaning and/or the necessity for replacement parts will be increased. If there
is any doubt regarding the suitability of a specific material, advise what material is to be used and/or submit a sample for test.
DESCRIPTION
SB-E-A1-2-8
©BINKS 1999
Chart 1 Ordering Information :
TUNG CARB
GROUP 1
Normal range of finishing materials from thin spirits to heavy enamels.
GROUP 4
Vitreous enamel. N.B Air nozzle can only be used with mat. Nozzles of the same group. Suffix “V” denotes tungsten carbide
tipped.
Figure in ( ) brackets is air consumption in c.f.m 63 psi
Figure in [ ] brackets is air consumption in m
3
/ hr at 63 psi

Binks 230 Specifications

General

Operating Pressure	40-60 PSI
Maximum Pressure	100 PSI
Air Inlet	1/4 inch NPT
Material	Aluminum
Application	Automotive Refinishing, Woodworking, General Industrial

Summary

Parts List

Operation

Connecting Gun to Air Hose

Details on connecting the spray gun to an air hose, including recommended hose bore and filter specifications.

Controlling the Material Flow

Explains adjustment of material flow using the Material Valve Control Screw for optimal spray output.

Adjustment of Material Needle Valve

Controlling the Fan Spray

Connecting Gun to Material Hose

Instructions for connecting the spray gun to the material supply hose, specifying bore size and connectors.

Connecting Gun to Syphon Cups

Procedure for attaching siphon cups to the gun's material connection, ensuring proper seal and cup lid positioning.

Safety Warnings

Fire and Explosion Precautions

Highlights risks of flammable materials, ventilation needs, smoking, and static electricity hazards.

Personal Protective Equipment

Emphasizes use of respiratory protection, eye protection, and gloves when handling materials.

Training and Safe Use

Misuse and Handling

Maintenance & Fault Finding

Cleaning Gun with Syphon Cup or Material Hose

Faulty Spray Troubleshooting

Intermittent Spray Issues

Air Leak at Air Valve Stem

Air Leaking Through the Gun

Paint Leaking at Needle Gland Seal