Binks AA1600M - User Manual

AA1600M AIR-AssIst
AIRLEss spRAy Gun
(0909-1600-XXXXXX)
(WItH FLAt tIp/tWIst tIp OptIOn,
FAn sIZE ADJustMEnt FEAtuRE AnD
HVLp/LVMp tECHnOLOGy)
Part
Sheet
77-2921R-9
The following instructions
provide the necessary
information for the proper
operation and preventive
maintenance of the Binks
AA1600M Air-Assist Airless
Spray Gun. Please read and
understand all information in this
document in order to get the
maximum performance from
your new AA1600M spray gun.
In the AA1600M spray gun, the
paint or other material to be
sprayed is pre-atomized and
forced through the carbide tip by
the typical 400-800 psi fluid
pressure (with capabilities up to
1,600 psi/110 bar). As a result of
the pre-atomizing, the final
shaping air supplied by the air
cap produces an exceptionally
fine and even spray pattern. The
result of this spray pattern is an
even finish that lends itself to
products that need an
exceptionally fine finish with
reduced overspray and VOC
emissions.
Replaces
Part Sheet
77-2921R-8
II 2 G X
SPECIFICATIONS:
Maximum
Fluid Pressure: 1600 psi/110 bar
Maximum
Air Pressure: 100 psi/6.8 bar
Gun Body: Forged Aluminum
Fluid Path: Stainless Steel
Fluid Seat: UHMW (Tungsten Carbide optional)
Fluid Inlet Size: 1/4" NPS(m) Thread
Air Inlet Size: 1/4" NPS(m) Thread
Gun Weight: 17.28 oz./490 g
(without Tip, Aircap, Guard)
READ ALL InstRuCtIOns BEFORE OpERAtInG tHIs BInKs pRODuCt
IMpORtAnt!
DO NOT DESTROY
It is the customer's responsibility to have
all operators and service personnel read
and understand this manual.
Contact your local Binks representative
for additional copies of this manual.
English: Pages 1 – 12
Español: Páginas S-1 – S-12
Français: Pages F-1 – F-12
PROP 65 WARNING
WARNING: This product
contains chemicals known
to the State of California
to cause cancer and birth
defects or other
reproductive harm.

Binks AA1600M Specifications

General

Brand	Binks
Model	AA1600M
Category	Paint Sprayer
Language	English

Summary

AA1600 M Air-Assist Airless Spray Gun

Product Specifications

Detailed technical specifications for the spray gun, including pressure and fluid capacity.

Important Safety Warnings and Cautions

Spray Gun Set-Up

Typical Hook-Up Diagram

Illustrates the standard connection of hoses and regulators for spray gun operation.

Fluid Tip Selection and Fluid Hoses

Guidance on choosing the correct fluid tip and fluid hoses for optimal performance.

Definitive Spray Pattern Troubleshooting

General Troubleshooting Guide

Maintenance and Cleaning Procedures

Spray Pattern Troubleshooting

Specific troubleshooting steps for various spray pattern issues.

Fluid Tip, Lubrication, and Cleaning

Details on fluid tip care, proper lubrication, and the cleaning process.

Replacing Fluid Nozzle and Needle Assembly

Replacing the Fluid Nozzle

Step-by-step instructions for replacing the fluid nozzle.

Replacing the Fluid Needle Assembly

Step-by-step instructions for replacing the fluid needle assembly.

Servicing the Air Valve

Reasons to Service Air Valve

Outlines the common reasons and scenarios requiring air valve service.

Replacing the Air Valve

Reasons to Replace Air Valve

Details the primary reasons and indicators for replacing the air valve.

Tip Guard Installation

Reason to Install Tip Guard

Explains the purpose and necessity of installing the tip guard.

Tip Selection Charts and Full Gun Assemblies

Parts List and Accessories