To Next PageTo Next PageWhat to do if Biostar TZ68A Motherboard system has no power?
If there is no power in the system, meaning the power LED does not shine and the fan of the power supply does not work, ensure the power cable is securely plugged in. If the issue persists, try replacing the cable. If problems still occur, contact technical support.
Why Biostar Motherboard system does not boot from a hard disk drive?
If your system does not boot from the hard disk drive, but can boot from the optical drive, check the cable running from the disk to the disk controller board to ensure both ends are securely plugged in. Also, check the drive type in the standard CMOS setup. Backing up the hard drive is extremely important, as all hard disks are capable of breaking down at any time.
What to do if Biostar TZ68A Motherboard system only boots from an optical drive?
If the system only boots from an optical drive, but hard disks can be read and applications can be used, back up data and applications files, reformat the hard drive, and reinstall applications and data using backup disks.
What to do if Biostar TZ68A shows 'Invalid Configuration' or 'CMOS Failure'?
If the screen message shows 'Invalid Configuration' or 'CMOS Failure', review the system’s equipment and make sure the correct information is in setup.
What to do if Biostar TZ68A Motherboard cannot boot after installing a second hard drive?
If the system cannot boot after installing a second hard drive, set master/slave jumpers correctly, run the SETUP program and select correct drive types, or call the drive manufacturers for compatibility with other drives.
Configures CPU features like active cores, CPUID maximum, and execute disable bit.
Configures PCI, PCI-X, and PCI Express settings, including latency and Snoop options.
Configures SATA modes (IDE, AHCI, RAID) and controller settings.
Manages USB settings including legacy support and EHCI hand-off.
Configures North Bridge parameters, including memory and graphics settings.
Configures South Bridge related settings like audio and USB controllers.
Manages onboard PCI Express devices like LAN and USB 3.0.
Sets the administrator password to limit access to BIOS setup.
Sets a power-on password required to boot or enter setup.
Adjusts the CPU ratio for performance tuning.
Manually or automatically regulates DRAM timing parameters.
Saves current settings and restarts the system.
Loads factory default BIOS settings to resolve issues.
Executes the UEFI BIOS built-in EFI Shell.
Configures CPU features like active cores, CPUID maximum, and execute disable bit.
Configures PCI, PCI-X, and PCI Express settings, including latency and Snoop options.
Configures SATA modes (IDE, AHCI, RAID) and controller settings.
Manages USB settings including legacy support and EHCI hand-off.
Configures North Bridge parameters, including memory and graphics settings.
Configures South Bridge related settings like audio and USB controllers.
Manages onboard PCI Express devices like LAN and USB 3.0.
Sets the administrator password to limit access to BIOS setup.
Sets a power-on password required to boot or enter setup.
Adjusts the CPU ratio for performance tuning.
Manually or automatically regulates DRAM timing parameters.
Saves current settings and restarts the system.
Loads factory default BIOS settings to resolve issues.
Executes the UEFI BIOS built-in EFI Shell.
General| Form Factor | ATX |
|---|---|
| Socket Type | LGA 1155 |
| Chipset | Intel Z68 |
| Memory Slots | 4 |
| Maximum Memory | 32GB |
| Audio | Realtek ALC892 |
| LAN | Realtek RTL8111E |
| PCI Express x1 | 2 |
| PCI Slots | 2 |
| SATA 6Gb/s | 2 |
| SATA 3Gb/s | 4 |
| USB 2.0 Ports | 6 |
| LAN Speed | 10/100/1000 Mbps |
| Audio Channels | 8 |
| RAID Support | RAID 0, 1, 5, 10 |
| Memory Standard | DDR3 2133/1866/1600/1333/1066 |
| PCI Express x16 | 2 |
| USB 3.0 Ports | 4 |
