Why is the pump on my Black & Decker BEPW1600LLP Pressure Washer so noisy?
If your Black & Decker Pressure Washer pump is excessively noisy, check that all hoses and fittings are airtight. Turn the machine off and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle.
What to do if Black & Decker BEPW1600LLP spray wand leaks?
A leaking spray wand may be due to improper attachment (insert the spray wand into the spray handle, push in, and turn to lock it in place).
What causes water leaks from the pump of Black & Decker Pressure Washer?
Water leaks from the pump can be caused by loose fittings (check that all fittings are tight). Water seals may also be damaged or worn.
Why is my Black & Decker BEPW1600LLP Pressure Washer pump excessively noisy?
An excessively noisy pump is often caused by the pump sucking air. To resolve this, check that hoses and fittings are airtight. Turn OFF the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle.
What causes output pressure varies high/low on Black & Decker Pressure Washer?
Inconsistent output pressure can stem from insufficient inlet water supply (turn water on full force and check the hose for leaks and kinks), the pump sucking air (ensure hoses and fittings are airtight, turn OFF the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle), a clogged water inlet screen (rinse with water to unclog), or an obstructed discharge nozzle (blow out or remove debris).
Why Black & Decker BEPW1600LLP Pressure Washer unit does not reach high pressure?
The unit may not reach high pressure if the water faucet isn't fully turned on (open the water valve fully), the water inlet filter is clogged (remove and rinse to clean), the nozzle is worn (replace with a new nozzle), the pump is sucking air (check that hoses and fittings are airtight, turn OFF the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle), the water supply is restricted (check the water hose for kinks, leaks, and blockages). Also, the unit may not be properly self-primed.
What to do if Black & Decker BEPW1600LLP Pressure Washer has no detergent?
If there's no detergent, the container might be empty (add more detergent), the bottle or suction tube may not be properly connected (check connections), the detergent could be too thick (use detergent recommended for pressure washers only), the filter on the suction tube could be clogged (run warm water through it), the suction tube might be damaged or clogged (remove obstruction or replace it), or the discharge nozzle is obstructed (blow out or remove debris).
Why is my Black & Decker BEPW1600LLP leaking water from the pump?
If water leaks from the pump of your Black & Decker Pressure Washer, make sure that all fittings are tight. If the water seals are damaged or worn, contact your local dealer.
Why is my Black & Decker BEPW1600LLP Pressure Washer spray wand leaking?
If the spray wand on your Black & Decker Pressure Washer leaks, make sure the spray wand is properly attached by inserting it into the spray handle and pushing it in and turning it to lock it into place. If the O-ring is broken, contact your local dealer.
How to fix a garden hose connection leak on my Black & Decker BEPW1600LLP Pressure Washer?
If the garden hose connection on your Black & Decker Pressure Washer leaks, tighten the fittings. If the rubber washer is missing or worn, replace it in the hose adapter.
General| Model | BEPW1600LLP |
|---|---|
| Brand | Black & Decker |
| Category | Pressure Washer |
| Power Source | Electric |
| Max Pressure | 1600 PSI |
| Water Flow | 1.2 GPM |
| Voltage | 120V |
| Hose Length | 20 ft |
| Nozzles Included | 3 |
To Next Page