How to fix a garden hose connection leak on my Black & Decker Pressure Washer?
If the garden hose connection on your Black & Decker Pressure Washer leaks, tighten the fittings. If the rubber washer is missing or worn, replace it in the hose adapter.
Why Black & Decker Pressure Washer motor does not start?
The motor may not start due to several reasons: the unit isn't plugged in (plug in the power cord); the ON/OFF switch is in the OFF position (turn the switch to the “ON” position); or the wand trigger isn't being squeezed (squeeze the trigger with the switch in the “ON” position).
What to do if Black & Decker BEPW2200 Pressure Washer motor buzzes but fails to run?
If the motor buzzes but doesn't run, it could be due to supply voltage being below the minimum (verify that only the pressure washer is running on the circuit), the system having residual pressure (turn the unit off, squeeze the trigger on the spray wand to release pressure, then turn the unit on), or voltage loss due to an extension cord (plug directly into the outlet).
How to fix garden hose connection leaks on Black & Decker BEPW2200?
Garden hose connection leaks are often due to loose fittings (tighten the fittings) or a missing/worn rubber washer (replace the washer in the hose adapter).
Why is my Black & Decker BEPW2200 not reaching high pressure?
If your Black & Decker Pressure Washer isn't reaching high pressure, fully open the water valve and check the water hose for any kinks, leaks, or blockages that may be restricting the water supply. Clean the water inlet filter by removing it and rinsing it. If the nozzle is worn, replace it with a new one. Ensure hoses and fittings are airtight, and purge the pump by turning off the machine and squeezing the trigger gun until water flows steadily from the nozzle. If the unit is not properly self-primed, refer to Self Priming under Assembly.
Why does my Black & Decker Pressure Washer pressure go up and down?
If the output pressure of your Black & Decker Pressure Washer varies, ensure you have enough inlet water supply by turning the water on full force and checking the hose for leaks and kinks. Also, check that the hoses and fittings are airtight, and purge the pump by turning the machine off and squeezing the trigger gun until a steady flow of water emerges from the nozzle. Clean the water inlet screen by rinsing it off with water, and clear any obstructions from the discharge nozzle.
What to do if my Black & Decker Pressure Washer motor buzzes but doesn't run?
If your Black & Decker Pressure Washer motor buzzes but fails to run, ensure that only the pressure washer is running on the circuit to verify the supply voltage is above the minimum. Turn the unit off, squeeze the trigger on the spray wand to release any residual pressure, and then turn the unit back on. Plug the unit directly into the outlet to avoid voltage loss from an extension cord. If the cleaner has not been used for a long period, contact your local dealer.
Why is my Black & Decker BEPW2200 not dispensing detergent?
If there is no detergent coming out of your Black & Decker Pressure Washer, first, ensure the detergent container is filled with detergent recommended for pressure washers only. Check that the detergent bottle or suction tube is properly connected. Clean the filter on the detergent suction tube by running warm water through it to remove any debris. If the detergent suction tube is damaged or clogged, remove the obstruction or replace the tube. Also, blow out or remove any debris from the discharge nozzle.
Why is the pump on my Black & Decker Pressure Washer so noisy?
If your Black & Decker Pressure Washer pump is excessively noisy, check that all hoses and fittings are airtight. Turn the machine off and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle.
Why is my Black & Decker BEPW2200 spray wand leaking?
If the spray wand on your Black & Decker Pressure Washer leaks, make sure the spray wand is properly attached by inserting it into the spray handle and pushing it in and turning it to lock it into place. If the O-ring is broken, contact your local dealer.
General| Brand | Black & Decker |
|---|---|
| Model | BEPW2200 |
| Category | Pressure Washer |
| Language | English |
Essential safety guidelines, warnings, and precautions for operating the pressure washer.
Guidelines for protecting others and understanding the meaning of tool labels and symbols.
Instructions for connecting the main handle and the spray handle to the unit.
Steps for attaching high pressure hose, garden hose, and connecting nozzles.
Steps to prepare the cleaning surface, the unit, and the spray handle.
Instructions for connecting the water supply and using detergents for cleaning.
How to start the unit, clean surfaces, and handle the spray wand.
Procedures for cleaning the pressure washer unit and its components for optimal care.
Steps for cleaning clogged nozzles and maintaining the water inlet filter.
To Next Page
